Sony VENICE 2 MPC-3626 Manual - Página 5

Navegue en línea o descargue pdf Manual para Cámara digital Sony VENICE 2 MPC-3626. Sony VENICE 2 MPC-3626 17 páginas. Digital motion picture camera, cinealtav 2

Imprimir página

Select Run.

The version upgrade starts.

The version upgrade is performed in two

steps called phase 1 and phase 2.

When the version upgrade starts, the

REC lamp flashes and a "Version Upgrade

Elapsed Time XX:YY:ZZ Executing... **%"

message appears on the viewfinder and

sub display (XX:YY:ZZ: Progress time in

each phase, **%: Progress status in each

phase).

The approximate time required for each

phase is shown below (the time will vary

depending on the combination of the old

and new upgrade versions).

Phase

Estimated time required

Phase 1

Approx. 10 minutes

Phase 2

Approx. 35 minutes

[Note]

When the version upgrade transitions from phase

1 to phase 2, the message disappears and the

unit restarts. The version upgrade process then

continues. Do not turn the unit off.

When the version upgrade is completed successfully,

the REC lamp turns on and a "Version Upgrade OK

Turn Power Off" message appears.

If the version upgrade stops, the version upgrade

data may be corrupted and a "Version Upgrade

NG: Cannot Read the File Turn Power Off" message

appears. Restart the MPC-3628/MPC-3626, save the

correct version upgrade data on the SD card, and

then perform the upgrade procedure again from

step 1.

If the version upgrade fails, a "Version Upgrade

Error!" message appears. Check the version upgrade

procedure, and then perform the upgrade procedure

again from step 1.

If the version upgrade problem persists and the

upgrade is not successful, there may be a problem

with the MPC-3628/MPC-3626. Contact a Sony

service representative.

Restart the MPC-3628/MPC-3626.

Check that the version has been updated

(see "Checking the Existing Version").

If the firmware has not been updated

to the latest version, check the version

upgrade procedure, and then perform the

upgrade procedure again from step 1.

Version Upgrade using

Recovery Mode (Forced

Version Upgrade)

If the user version upgrade fails, a problem

may have occurred in internal memory. The

problem in internal memory may also have

occurred due to another error. When a problem

in internal memory occurs, an error may be

issued or the MPC-3628/MPC-3626 may not

turn on. In such cases, you can forcibly write

the software to the MPC-3628/MPC-3626 using

recovery mode. The MPC-3628/MPC-3626 will

operate normally once the problem is resolved.

[Notes]

Executing the procedure in this section will restore the

MPC-3628/MPC-3626 software to factory defaults, and

user settings will be lost. User settings are maintained

in a normal version upgrade, so you should upgrade

from the setup menu.

Always connect an AC adaptor with power supply

rating of 120 W or higher when upgrading. If a battery

pack is attached at the same time, the upgrade

will continue if the AC adaptor is subsequently

disconnected.

If the problem persists after recovery using this

function, contact a Sony service representative.

Required item

Prepare an SD card or SDHC card on which the

version upgrade data is saved.

Procedure

Insert the SD card into the MPC-3628/

MPC-3626.

[Note]

Set the power switch of the MPC-3628/MPC-3626 to

the OFF position, and then insert the SD card.

Press and hold the MENU button together

with the CLIPS and ASSIGN 2 buttons on

the Assistant side, and set the power

switch to the ON position.

The REC lamp of the MPC-3628/MPC-3626

starts flashing and the software recovery

begins.

When finished, the REC lamp stops

flashing and the MPC-3628/MPC-3626

automatically restarts.

[Notes]

When the REC lamp starts flashing, release the

buttons.

The version upgrade process using recovery

mode takes about 55 minutes.

The version upgrade progress may not be

displayed depending on the state of the unit.

Turn the MPC-3628/MPC-3626 off.

Remove the SD card from the MPC-3628/

MPC-3626.

Turn the MPC-3628/MPC-3626 on, and

check that the unit starts normally.

Check that the version has been updated

(see "Checking the Existing Version").