Sony MEX-N5000BT Manual de instrucciones - Página 25
Navegue en línea o descargue pdf Manual de instrucciones para Sistema estéreo Sony MEX-N5000BT. Sony MEX-N5000BT 40 páginas. Bluetooth audio system
También para Sony MEX-N5000BT: Manual de instrucciones (32 páginas), Instalación (2 páginas)
Imprimir página
The sound is intermittent.
-+ The sound may be intermittent at a high-bit-rate
of more than 320 kbps.
Pandora® connection is not possible.
-+ Shut down the Pandora® application on the
mobile device, and then launch it again.
Application name is mismatched with the actual
application in App Remote.
-+ Launch the application again from the "App
Remote" application.
One touch connection (NFC) is not possible.
-+ If the smartphone does not respond to the
touching.
-Check that the NFC function of the smartphone
is turned on.
-Move theN-Mark part of the smartphone
closer to the N-Mark part on this unit.
- If the smartphone is in a case, remove it.
-+ NFC receiving sensitivity depends on the device.
If One touch connection with the smartphone
fails several times, make BLUETOOTH connection
manually.
The connecting device cannot detect this unit.
-+ Before the pairing is made, set this unit to pairing
standby mode.
-+ While connected to a BLUETOOTH device, this
unit cannot be detected from another device.
-Disconnect the current connection and search
for this unit from another device.
-+ When the device pairing is made, set the
BLUETOOTH signal output to on (page 7).
Connection is not possible.
-+ The connection is controlled from one side (this
unit or BLUETOOTH device), but not both.
-Connect to this unit from a BLUETOOTH device
or vice versa.
The name of the detected device does not
appear.
-+ Depending on the status of the other device, it
may not be possible to obtain the name.
No ringtone.
-+ Adjust the volume by rotating the control dial
while receiving a call.
-+ Depending on the connecting device, the
ringtone may not be sent properly.
-Set [RINGTONE] to [1] (page 19).
-+ The front speakers are not connected to the unit.
-Connect the front speakers to the unit. The
ringtone is output only from the front speakers.
The talker's voice cannot be heard.
-+ The front speakers are not connected to the unit.
-Connect the front speakers to the unit. The
talker's voice is output only from the front
speakers.
A call partner says that the volume is too low or
high.
-+ Adjust the volume accordingly using mic gain
adjustment (page 15).
Echo or noise occurs in phone call conversations.
-+ Lower the volume.
-+Set EC/NC Mode to [EC/NC-1] or [EC/NC-2]
(page 15).
-+ If the ambient noise other than the phone call
sound is loud, try reducing this noise.
E.g.: If a window is open and road noise, etc., is
loud, shut the window. If an air conditioner is
loud, lower the air conditioner.
The phone is not connected.
-+ When BLUETOOTH audio is played, the phone is
not connected even if you press CALL.
-Connect from the phone.
The phone sound quality is poor.
-+ Phone sound quality depends on reception
conditions of cellular phone.
- Move your car to a place where you can
enhance the cellular phone's signal if the
reception is poor.
The volume of the connected audio device is low
(high).
-+ Volume level will differ depending on the audio
device.
-Adjust the volume of the connected audio
device or this unit.
The sound skips during playback of a
BLUETOOTH audio device.
-+ Reduce the distance between the unit and the
BLUETOOTH audio device.
-+ If the BLUETOOTH audio device is stored in a case
which interrupts the signal, remove the audio
device from the case during use.
-+ Several BLUETOOTH devices or other devices
which emit radio waves are in use nearby.
-Turn off the other devices.
- Increase the distance from the other devices.
-+ The playback sound stops momentarily when the
connection between this unit and the cellular
phone is being made. This is not a malfunction.
The connected BLUETOOTH audio device cannot
be controlled.
-+ Check that the connected BLUETOOTH audio
device supports AVRCP.
25GB