Sony MHC-RG221 Manual de instrucciones - Página 35

Navegue en línea o descargue pdf Manual de instrucciones para Sistema estéreo Sony MHC-RG221. Sony MHC-RG221 48 páginas. Sony operating instructions owner's record mini hi-fi component system mhc-gx750, gx450, gx250, mhc-rg555, rg551s, rg444s, rg441, rg333, rg222, rg221, rg121, rg100, mhc-rx550
También para Sony MHC-RG221: Manual de instrucciones (47 páginas)

Imprimir página

Tuner

Severe hum or noise/stations cannot be

received. ("TUNED" or "STEREO" flashes in

the display.)

• Set the proper band and frequency (page 15).

• Connect the antenna properly (page 8).

• Find a place and an orientation that provide good

reception, then set up the antenna again. If you

cannot obtain good reception, we recommend you

connect a commercially available external

antenna.

• The supplied FM lead antenna receives signals

along its entire length, so make sure you extend it

fully.

• Locate the antennas as far away from the speaker

cords as possible.

• Try turning off surrounding electrical equipment.

A stereo FM program cannot be received in

stereo.

• Press FM MODE repeatedly until "STEREO"

appears.

Tape deck

The tape does not record or play, or there is a

decrease in sound level.

• The heads are dirty. Clean them (page 38).

• The record/playback heads are magnetized.

Demagnetize them (page 38).

The tape does not erase completely.

• The record/playback heads are magnetized.

Demagnetize them (page 38).

There is excessive wow or flutter, or the sound

drops out.

• The capstans or pinch rollers are dirty. Clean them

(page 38).

Noise increases or the high frequencies are

erased.

• The record/playback heads are magnetized.

Demagnetize them (page 38).

The tape does not record.

• No cassette is loaded. Load a cassette.

• The tab has been removed from the cassette.

Cover the broken tab with adhesive tape

(page 38).

• The tape has wound to the end.

Transmitter (MHC-GX750 only)

There is no sound.

• Check the connection of the optional component.

• Check that the optional component is turned on.

• Turn up the volume on the connected optional

component, if the transmitter is connected to the

headphones jack.

• Change the radio frequency using the CHANNEL

selector on the transmitter, then press WIRELESS

on the unit again.

• If you connect the transmitter to the analog out

jacks of an audio reproducer, make sure that the

NOISE FILTER switch is set to OFF.

• Make sure that the NOISE FILTER switch is set

to either ON or OFF (If the switch gets stuck

between ON and OFF, the sound will be cut off).

There is severe hum or noise.

• If the transmitter is connected to the headphones

jack, turn down the volume of the connected

optional component. If the connected optional

component has the BASS BOOST or MEGA

BASS function, set these function to OFF.

• If the connected optional component has a LINE

OUT jacks, connect its LINE OUT jacks.

• Change the radio frequency with the CHANNEL

selector on the transmitter then press WIRELESS

on the unit again.

• If you connect the transmitter to the analog out

jacks of an audio reproducer, make sure that the

NOISE FILTER switch is set to OFF.

If the system still does not

operate properly after performing

the above measures, reset the

system as follows:

Use buttons on the unit for the operation.

Disconnect the power cord.

Reconnect the power cord.

Press x, PLAY MODE/TUNING MODE and

DISC 1 at the same time.

Press ?/1 to turn on the system.

The system is reset to the factory settings. You

should set the settings you made, such as the

preset stations, clock, and timer.