Sony STR-DA80ES - Fm Stereo / Fm-am Receiver Manual de instrucciones - Página 29

Navegue en línea o descargue pdf Manual de instrucciones para Sistema estéreo Sony STR-DA80ES - Fm Stereo / Fm-am Receiver. Sony STR-DA80ES - Fm Stereo / Fm-am Receiver 40 páginas. Limited warranty (es products)
También para Sony STR-DA80ES - Fm Stereo / Fm-am Receiver: Manual de instrucciones (39 páginas), Antecedentes técnicos (38 páginas), Garantía limitada (1 páginas)

Imprimir página
Sony STR-DA80ES - Fm Stereo / Fm-am Receiver Manual de instrucciones

Programming the Remote

The RM-P501 remote included with the receiver can
control non-Sony components by "learning" the
control signals from their remotes. Once this remote
learns the other components signals, you can use these
components as part of your system. Additionally, if
you have any Sony components that fail to operate
with this remote, use this programming function. This
remote can "learn" signals only from other infrared
wireless remotes. Before you program signals, make
sure that the two remotes:
• Face straight at each other (see Step 3 below)
• Are placed at a distance of about 2 inches (5 cm)
• Are not moved during programming
LEARN indicator
SLEEP
LEARN
SYSTEM CONTROL / FUNCTION
VIDEO 1
VIDEO 2
SYSTEM
(AUTO CATEGORIZE SYSTEM)
TAPE
DAT/MD
TV
CONTROL/
CONTROL
1
ON
FUNCTION
4
7
BACK
GROUND
SHIFT
>
10
–
+
SUB CH
POSITION
0
)
— RMS —
DIRECTION
9
(
— SOUND FIELD —
ON/OFF
GENRE
EQ/
BAND
TONE
DIGTAL
DIRECT
PROCESSING
CONTROL
DPC
MODE
PROGRAMMABLE
1
Press the SYSTEM CONTROL/FUNCTION
button of the component you want to program
(except the TUNER and PHONO buttons).
For example, if you want to program a CD player's
remote, press CD.
2
Press LEARN to turn on the LEARN indicator.
3
Press the button on this unit's remote that is to
"learn" the signal from the other remote.
The LEARN indicator flashes slowly.
Use only the shaded buttons shown above (see
"Remote Button Descriptions" on page 36 for the
buttons you can use to operate each component).
Other remote
About 2 inches
(5 cm)
VISUAL POWER
SYSTEM OFF
VISUAL
LEARN
POWER
SYSTEM OFF
VIDEO 3
LD
TV
CD
TUNER
PHONO
5.1
INPUT
2
3
TV/VIDEO
5
6
D.TUNING
DISC
8
9
+
CH/
ENTER
PRESET
0
–
RMS/START
ANT
SWAP
TV/VTR
=
+
D. SKIP
CLEAR
P IN P
JUMP
p
P
r
TEST
MODE
TONE
SLOPE
— LEVEL —
+
+
REAR
CENTER
–
–
MASTER
BASS
VOL
BOOST
MUTING
MASTER VOL –
Receiver's remote
Advanced Remote Operations
If the LEARN indicator flashes rapidly
You cannot use the button you've pressed.
4
On the other remote, select the function that the
receiver's remote is to "learn" and hold down its
button until the LEARN indicator lights steadily.
5
Repeat Steps 3 and 4 to program other buttons.
Note that each button can only "learn" one signal
from another remote.
6
Press LEARN.
After the LEARN indicator turns off, you can
control the other component with the programmed
buttons.
z
When you program the recording signal
Use the r button to memorize the signal.
z
If you cannot successfully program signals, check the
following:
• If the LEARN indicator does not light up at all, the
batteries are weak. Replace both batteries.
• If the LEARN indicator does not flash or light up in
Step 3 or 4, there is interference. Clear the signal as
described in "Clearing the programmed signals"
below and program again from the beginning.
• The two remotes are placed too far apart. Make sure
they are only 2 inches apart.
• If you don't proceed to the following steps within
about 1 minute during Steps 2 and 3, the remote
automatically exits learning mode. Start again from
Step 2.
• If the memory in the remote has become full (If you
program signals of Sony components, you can store
about 60 signals.), you can program a new signal on a
previously programmed button, but the new signal
will replace the previously programmed one.
Notes
• You cannot turn on programmed components by pressing
a SYSTEM CONTROL/FUNCTION button. You have to
turn on the component's power switch.
• Do not program remote signals of air conditioners or other
household appliances.
Clearing the programmed signals
To clear all the programmed signals, do the following.
The button's functions are reset to the factory-preset.
1
Press LEARN to turn on the LEARN indicator.
2
Hold down SYSTEM OFF, VISUAL POWER, and
MASTER VOL – until the LEARN indicator
flashes three times and then turns off.
Getting Started
29