Cisco ASR 9000 Series Manual - Página 13
Navegue en línea o descargue pdf Manual para Hardware de red Cisco ASR 9000 Series. Cisco ASR 9000 Series 44 páginas. Line card
También para Cisco ASR 9000 Series: Configuración de los ajustes de red (26 páginas), Manual de configuración (46 páginas), Manual de configuración (50 páginas), Manual (24 páginas), Configuración de (46 páginas), Manual de consulta rápida (7 páginas)
Imprimir página
- 1. Field Replaceable Units
- 2. Online Insertion and Removal
- 3. Powering off the Router
- 4. Replacing the Chassis Air Filter
- 5. Required Tools and Equipment
- 6. Removing a Fan Tray
- 7. Installing a Fan Tray
- 8. Disconnecting AC Power
- 9. Reconnecting AC Power
- 10. Disconnecting DC Power
- 11. Reconnecting DC Power
Replacing Cisco ASR 9000 Series Router Components
Procedure
Step 1
Before making any physical changes, check the software configuration to ensure no ROMMON variable
CHASSIS_TYPE (such as CHASSIS_TYPE=10_SLOT) is set to override the chassis type.
Step 2
At the Cisco IOS-XR command prompt on the RSP console, run the pwrmod_change command. This
command displays the current power module and system information.
Example:
RP/0/RSP0/CPU0:RO9_P2RSP3# run
Wed Jul
# pwrmod_change
Current system:
power supply type : AC power supply version 2
chassis type : 10-slot
chassis bpid: 0x2fa, PID: ASR-9010-AC
UDI name: ASR-9010 AC, UDI desc: ASR-9010 AC
Step 3
Enter your new power module type.
Example:
Please enter the number that corresponds to the power supply type that is being migrated
to. Do not enter the current power system information, use the future power system type.
1)
2)
3)
4)
5)
6)
ATTENTION: You are about to commit a change in the power system type for the chassis.
Please confirm that the OLD and NEW power system information listed here is correct.
Once the system software change is committed, you must physically remove the OLD power
system and replace it with the NEW power system of the type specified below here. Any
mismatch between the programmed system value and the actual physical installation may
cause boot and power management issues in the system.
OLD POWER SYSTEM:
power supply type: AC power supply version 2
chassis type: 10-slot
chassis bpid: 0x2fa, PID: ASR-9010-AC
UDI name: ASR-9010 AC, UDI desc: ASR-9010 AC
NEW POWER SYSTEM:
power supply type: DC power supply version 2
chassis type: 10-slot
chassis bpid: 0x2fa, PID: ASR-9010-DC
UDI name: ASR-9010 DC, UDI desc: ASR-9010 DC
Step 4
Confirm your choice.
Example:
Please confirm that you wish to upgrade from AC power supply version 2 power system to
DC power supply version 2 power system by typing "yes" at the prompt below. Any other
response will cancel the power system change operation [yes/cancel]?
yes
Step 5
After the success message appears, power down the chassis.
4 20:18:58.034 UTC
AC power supply version 1, fits 3 across in single power shelf
DC power supply version 1, fits 3 across in single power shelf
AC power supply version 2, fits 4 across in single power shelf
DC power supply version 2, fits 4 across in single power shelf
AC power supply version 3, fits 3 across in single power shelf
DC power supply version 3, fits 4 across in single power shelf
Changing Between Version 1, Version 2, Version 3, AC, and DC Power Modules
Replacing Cisco ASR 9000 Series Router Components
13