Digitrax SDH104K1A Manual del usuario - Página 11

Navegue en línea o descargue pdf Manual del usuario para Media Converter Digitrax SDH104K1A. Digitrax SDH104K1A 12 páginas. Plug n’ play mobile decoder with soundfx

Imprimir página

2. Check your installation to make sure the decoders are installed properly.

If the sound output sounds distorted

1. Check the speaker cone for magnetic debris that may have collected there.

Debris on the speaker will cause a loss of sound quality and must be removed.

2. Be sure that the CV58 volume is not set at a level that is too high for the

speaker. For impedances below 32ohms (e.g. 8 to 30 ohms) set the volume set-

ting lower to ensure the 1 watt output rating is not exceeded.

If the LEDs do not respond to F0:

1. Be sure the locomotive address you are using to send the command is actu-

ally the address programmed into the decoder.

2. Make sure you have good electrical connections between the FN04K1 to the

SDH104K1A. We recommend soldering these connections for best reliability.

If the sound in your decoder shuts down after you stop it and you are not

using a Digitrax system for control. On some DCC systems decoders are not

addressed by DCC packets after the locomotive is set to 0 speed. In this case

after the CV11 timeout elapses (6 second default), sound will "shutdown.". To

defeat this feature, set CV11=00 to remove the timeout and shutdown. To make

sounds, the decoder must have a command addressed to it at least once.

If you have trouble reading back on the programming track, this may be

due to your system using Direct Bit mode for Service Mode readback. This cre-

ates difficulty reading two decoders in a locomotive that may have different

data or responses. Since the SDH104K1A and FN04 are actually two decoders,

you'll need to use standard direct mode for reading back CV values on the pro-

gramming track. Of course you can always just re-program the CV value into a

CV to get the desired results. OPs mode is recommended for programming all

CVs except CV01, CV17 & CV18 (2 digit and 4 digit addresses).

W W a a r r r r a a n n t t y y & & R R e e p p a a i i r r

All warranties on Digitrax products are limited to refund of purchase price,

repair or replacement at Digitrax's sole discretion. Except as expressly stated in

the full warranty statement, there are no warranties, express or implied, includ-

ing but not limited to any warranties of merchantability or fitness for a particu-

lar purpose. For complete warranty details see www.digitrax.com.

Damaged decoders should be returned directly to Digitrax for repair.

Incorporates elements of US Patents 6220552, 6545886, 6729584, 6747579,

other patents pending.

2 2 4 4 4 4 3 3 T T r r a a n n s s m m i i t t t t e e r r R R D D

P P a a n n a a m m a a C C i i t t y y , , F F l l 3 3 2 2 4 4 0 0 4 4

w w w w w w . . d d i i g g i i t t r r a a x x . . c c o o m m

Digitrax, Inc. is not responsible for unintentional

errors or omissions in this document.

www.digitrax.com

8 8 5 5 0 0 - - 8 8 7 7 2 2 - - 9 9 8 8 9 9 0 0

T T

8 8 5 5 0 0 - - 8 8 7 7 2 2 - - 9 9 5 5 5 5 7 7

F F

s s a a l l e e s s @ @ d d i i g g i i t t r r a a x x . . c c o o m m

E E