Epson Stylus Photo RX600 Información sobre el producto - Página 15

Navegue en línea o descargue pdf Información sobre el producto para Escáner Epson Stylus Photo RX600. Epson Stylus Photo RX600 19 páginas. Product support bulletin(s)
También para Epson Stylus Photo RX600: Consejos (2 páginas), Hoja de información del producto (4 páginas), Folleto (2 páginas), Manual de instalación (2 páginas), Manual Start Here (10 páginas), Manual de inicio rápido (28 páginas), Manual del usuario (12 páginas), Actualización (1 páginas), Boletín de asistencia sobre productos (6 páginas), Boletín de asistencia sobre productos (1 páginas), Especificaciones (2 páginas), Cómo copiar e imprimir (20 páginas), Manual de instrucciones (4 páginas)

Epson Stylus Photo RX600 Información sobre el producto
If you don't see any improvement after cleaning three or four
times, check the troubleshooting solutions in the User's Guide.
You can also turn the RX600 off and wait overnight—this
allows any dried ink to soften—and then try cleaning the print
head again.
Caution:
When you don't turn on your RX600 for a long time, the print quality
can decline. It's a good idea to turn it on at least once a month to
maintain good print quality.

Replacing Ink Cartridges

When the red ! light flashes, one or more ink cartridges are
low on ink. When your ink starts getting low, make sure you
have replacement cartridges available. You can't print if a
cartridge is empty.
When the red ! light stays on, you need to replace the
cartridge(s).
When you print with low or
empty ink cartridges, you'll
see a message on your RX600
screen. Check the icon in the
upper right corner to see which cartridge is low or empty:
If you can't see the icon clearly enough, press the
button, then press the d button to select
. Use the l and r buttons to decrease or increase
Adjustment
the contrast as necessary to see the icon clearly, then press the
button.
OK
When a cartridge is more than six months old, you may need
to replace it if printouts don't look their best. If the quality
doesn't improve after cleaning and aligning the print head,
you can replace the cartridge even if the red ! light is off.

Checking the Ink Supply

To check your ink supply, do the following:
1. Press the
button to enter setup mode.
Setup
2. Press the u and d buttons to select
the
button.
OK
You see a graphic with the amount of ink available in each
cartridge:
(Black)
(Cyan),
B
C
(Magenta),
(Light Magenta), and
M
LM
3. When you're done checking the ink levels, press the
button.
When your ink starts getting low, make sure you have
replacement cartridges available. You can't print if a cartridge
is empty.
Ink levels
Setup
LCD Contrast
, then press
Ink Levels
(Light Cyan),
LC
(Yellow).
Y
OK
Ink Cartridge Precautions
Warning:
Keep ink cartridges out of the reach of children.
If ink gets on your hands, wash them thoroughly with soap and
water. If ink gets in your eyes, flush them thoroughly with water.
Caution:
To avoid damaging the printer, never move the print head by hand.
You can't print if an ink cartridge is empty. Leave the empty
cartridge installed in the RX600 until you have obtained a
replacement. Otherwise the ink remaining in the print head nozzles
may dry out.

Removing and Installing Ink Cartridges

Be sure you have a new ink cartridge before you begin. Once
you start replacing a cartridge, you must complete all the steps
in one session.
1. If an ink cartridge is empty:
Look at the icon in the upper right corner of the LCD
screen to see which cartridge is empty, then press the
button.
If an ink cartridge is low:
Press the
button to enter setup mode. Press the u
Setup
and d buttons to select
again. Look at the icon in the upper right corner of the
OK
LCD screen or check the ink levels as described in
"Checking the Ink Supply" on page 15.
2. Use the side grips to open the scanner unit, as shown,
making sure to keep the scanner lid closed on top.
2/04
Epson Stylus Photo RX600
, press
, then press
Ink Cartridge
OK
Epson Stylus Photo RX600
OK
- 15