Dillinger Labs Aquarius Manual del usuario - Página 18
Navegue en línea o descargue pdf Manual del usuario para Altavoces Dillinger Labs Aquarius. Dillinger Labs Aquarius 18 páginas.
También para Dillinger Labs Aquarius: Manual del usuario (19 páginas)
Imprimir página
Question
How does the
You can store up to 10 SKAA transmitters on your Green List. These are your "favourite" audio
Green List work?
sources. Every time you add a transmitter, it is assigned the first open spot on the Green List. When
you single click the
hunts for radio stations when you press seek. If the Indicator is dim Green and flashes every few
seconds, this tells you the receiver is hunting through the Green List. Say you have 5 transmitters on
your Green List; your receiver will hunt through the list one by one: 1, 2, 3, 4, 5 and then back to 1
and so on. The dim Green Indicator flashes every time the receiver moves to the next spot on the list.
This hunting goes on for up to 1 minute. If your receiver doesn't find any of your favourite
transmitters, it stops hunting and just waits for the last bonded favourite. If your receiver does find
one of your favourite transmitters, the hunting stops, the Indicator turns bright green, and your
receiver starts playing audio from that favourite. A dim Green Indicator that is NOT flashing means
the receiver is just sitting on one spot, waiting for a specific favourite transmitter to show up.
How do I bond
Play audio from your source device and ensure it has a SKAA transmitter connected. Click the
with a specific
Bond Button on your receiver. The receiver hunts through the Green List, flashing the Indicator as it
Green transmitter?
goes. Once your receiver finds one of your favourite transmitters, it bonds to it and plays audio from
that transmitter. If that isn't the transmitter you wanted, click the Bond Button once more. Repeat
until your receiver bonds with the transmitter you want and you're hearing the correct audio playing.
How do I select
Say you want to put your receiver on a high shelf where you can't reach the Bond Button easily. First,
transmitters if I
set up your Green List: add all of the transmitters you'll want to use. Then 4-click the
can't reach my
Button to enter Red Mode. Now put the receiver up on the high shelf. Power on just one of your
Bond Button?
transmitters and power off all others. The receiver automatically bonds to the transmitter that's on.
How do I delete a
Factory Reset (6 Clicks of the Bond Button) clears the Green List and lets you start over from scratch.
transmitter from
If however, you'd like to delete just one transmitter from your Green List, first bond your receiver to
my Green List?
the transmitter you wish to delete. See the section above: How do I bond with a specific Green
transmitter?. Once you are bonded to it, hold down the
you see the Indicator flash Red —this Red flash means the transmitter has been deleted.
What is a Cluster?
Clusters are an optional convenience for "power users". A Cluster is several SKAA receivers
behaving as one product. A left & right speaker pair, for example, or a sound bar and subwoofer.
What is the Master
In any Cluster, there is a single Master receiver, and all of the other receivers in the Cluster follow its
receiver?
behaviour. You can control the entire Cluster by operating the
receiver must have a physical Bond Button in order to become the Master.
How do I
Do the Make a Cluster of Receivers procedure once for each receiver, but omit Step 3. Do them one
"uncluster" several
at a time. This gives each of the receivers a functioning
receivers?
thereafter operate independently.
What are some
Each step in the Make a Cluster of Receivers procedure has a 10-second time limit. When you see
tips for making
the Master's Indicator start to flash Red, you have 10 seconds to power on the next receiver. When
Clusters?
that receiver's Indicator starts to flash Red, you have 10 more seconds to power on the next one, and
so on.
Why does only
When you make a Cluster from several receivers, the first one powered on in the Make a Cluster of
one of my Bond
Receivers procedure becomes the Master of the Cluster. Only the Master's
Buttons work?
because a Cluster uses just one Green List —the Master's Green List. The Bond Button of each of the
other receivers will work only for the Mute / Unmute function (3-Click of the Bond Button).
Can any group of
No. The receivers must be members of the same product family. If they are not, the Make a Cluster
receivers be made
of Receivers procedure won't work. This is because only receivers which were designed to work
into a Cluster?
together (as a single product) can be made into a Cluster.
QUESTIONS AND ANSWERS
Answer
Bond Button, the receiver hunts through the Green List much like a car radio
Bond Button for a few seconds until
Bond Button of the Master. A
Bond Button, and each of them will
Bond Button works
Bond