Motorola C1001LB+ Manual del usuario
Navegue en línea o descargue pdf Manual del usuario para Teléfono inalámbrico Motorola C1001LB+. Motorola C1001LB+ 2 páginas.
También para Motorola C1001LB+: Manual (2 páginas)
Imprimir página
Digital Cordless Telephone
Motorola C1LB+
For C1001LB+, C1002LB+, C1003LB+ and C1004LB+
Warning: Charge the handset for 24 hours before use.
1. Getting started
IMPORTANT
Do not place your C1LB+ in the bathroom or other humid areas.
Location
You need to place your C1LB+ base within 1.5 metres of the mains power and telephone wall
socket so that the cables will reach. The socket-outlet should be installed near the equipment and
should be easily accessible.
Make sure that it is at least 1 metre away from other electrical appliances to avoid interference.
Your C1LB+ works by sending radio signals between the handset and base. The strength of the
signal depends on where you place the base. Placing it as high as possible ensures the best
signal.
HANDSET RANGE
The unit has a range of up to 300 metres outdoors when there is a clear line of sight between
the base and handset. Any obstruction between the base and handset will reduce the range
significantly. With the base indoors and the handset either indoors or outdoors, the range will
normally be up to 50 metres. Thick concrete and stone walls can severely affect the range.
SIGNAL STRENGTH
The
icon on your handset indicates that you are within range of the base. When out of range
of the base, the
icon flashes. If you are on a call, you will hear a warning beep.
The line will hang up if the handset moves out of range of the base. Move closer to the base. The
handset will automatically reconnect to the base.
Setting up
IMPORTANT
The base station must be plugged into the mains power at all times. Do not connect the
telephone line cord into the wall socket until the handset is fully charged. Use only the power
adaptor and telephone line cord supplied with the product.
Connecting the base
1. Plug the telephone line cord into the socket marked
on the underside of the base.
2. Plug the power adaptor into the socket marked
on the underside of the base and plug the
other end into the mains power wall socket. Switch on the mains power.
Handset LCD Display
Battery
Eco mode
status
Circle around
Scrolls
appears when
when
Eco mode is ON
charging
Time or Handset name
In standby mode, press and hold to switch handset
0
idle screen between handset name or time.
Flashes to indicate an incoming external call.
External call in progress.
Flashes to indicate an incoming internal call.
Internal call in progress.
3-way call in progress or transfer an external call to another C1LB+ handset registered to the
base.
Eco mode is ON.
Flashes to indicate new voicemail messages received. Off when you have no voicemail
messages.
1
Indicates signal strength.
Flashes when handset is not registered to the base or if you go out of range.
Hands-free mode is ON.
Menu is opened.
Phonebook is opened.
Flashes to indicate new calls list entries received.
2
Answered call (when viewing the Calls list).
2
Unanswered call (when viewing the Calls list).
2
Keypad is locked.
Displayed number is longer than 12 digits.
The approximate power levels of your battery are indicated as follows:
Battery is fully charged.
Battery is partially charged.
Battery is running low.
#
2. When the other handset answers, press
to connect all three callers to begin the
conference call.
icon is displayed.
I
3. If there is no answer from the other handset, press
to return to your external caller.
n
4. Press
to end the call.
3.6
Hands-free speakerphone
Hands-free lets you talk to your caller without holding the handset. It also enables other people in
the room to listen to the conversation over the loudspeaker.
3.6.1
Make a hands-free call
t
1. Dial the number and then press
twice.
icon is displayed and you will hear the call over the handset loudspeaker.
t
2. Press
to switch the call between the earpiece and the loudspeaker.
n
3. Press
to end the call.
NOTE
u
d
During a hands-free call, press
or
to adjust the volume.
3.6.2
Answer a call hands-free
If the handset is on the base and auto answer is switched on, lift the handset and press
t
If the handset is off the base or auto answer is switched off, press
twice to answer the call.
3.6.3
Switch to hands-free during a call
t
During a call, press
to put the call on the loudspeaker.
t
To switch hands-free off and return the call to the earpiece, press
again.
3.7
Redial
The last 10 entries dialled are stored in the redial list.
3.7.1
View or dial an entry
r
1. Press
to open the Redial list.
u
d
2. Scroll
or
to the entry you want.
t
n
3. Press
to dial the displayed entry or press
to return to standby.
NOTE
m
If the caller's number exactly matches an entry stored in the phonebook, the name is displayed.
Press
to see the caller's number.
3.7.2
Copy a Redial list number to the phonebook
r
1. Press
to open the Redial list.
u
d
2. Scroll
or
to the entry you want.
Manufactured, distributed or sold by Suncorp Technologies Ltd., official licensee
for this product. MOTOROLA and the Stylized M Logo are trademarks or registered
trademarks of Motorola Trademark Holdings, LLC. and are used under license. All
other trademarks are the property of their respective owners. © 2014 Motorola
Mobility LLC. All rights reserved.
Version 4 (SG)
Installing and charging the handset
1. Remove the battery cover from the back of the handset and insert the rechargeable Ni-MH
battery cells supplied. Please note the '+' and '-' markings inside the battery compartment
and insert in the correct direction.
2. Slide the battery cover back into place.
3. If you are charging the batteries for the first time, place the handset on the base to charge for
at least 24 hours continuously.
4. When the handset is fully charged,
icon will appear steady on the display. Plug the other
end of the telephone line cord (make sure that one end is already plugged into the base) into
the telephone wall socket.
Connecting the handset and charger
(for multi-pack only)
If you have purchased a multiple pack, you will need to carry out this process for all the handsets
and chargers.
1. Plug the power adaptor into the socket marked
on the underside of the charger and plug
the other end into the mains power wall socket.
2. Remove the battery cover from the back of the handset and insert the 2 x AAA NiMH
rechargeable batteries supplied. Please note the '+' and '-' markings inside the battery
compartment and insert in the correct direction.
3. Slide the battery cover back into place.
If you are charging the batteries for the first time, place the handset on the charger to charge for
at least 24 hours continuously.
4. When the handset is fully charged,
icon will appear steady on the display. The display will
show
HANDSET
and handset number (e.g. 2) to indicate that it is registered to the base.
IMPORTANT
Warning! Use only the approved rechargeable Ni-MH battery cells (2 x AAA Ni-MH 300mA
rechargeable batteries) supplied with your C1LB+.
Please do not use alkaline or non rechargeable batteries. It may cause permanent damage to
the product and void the warranty.
BATTERY LOW WARNING
If
icon flashes on the display and you hear a warning beep every minute during a call, you
will need to recharge the handset before you can use it again.
When charging,
icon will scroll on the display. Once fully charged scrolling will stop.
Flashes when battery is almost fully discharged.
1
This feature is dependent on your Network Service provider supporting the service. A
subscription fee may be payable.
2
For this feature to work, you must subscribe to Caller ID Service from your network operator. A
subscription fee may be payable.
Underside of the base
A Page
In standby mode, press to ring the handset(s).
Press and hold to enter registration mode when registering handsets.
Navigating the menus
Your C1LB+ has an easy to use menu system.
Each menu has a list of options, which you can see on the menu map on the following page.
When the handset is switched on and in standby:
m
1. Press
to open the main menu.
u
d
2. Then use
or
buttons to scroll through the available options.
m
3. Press
to select an option. To return to the previous menu level, press
n
menu and return to standby, press
.
NOTE
If no buttons are pressed for 20 seconds, the handset returns to standby automatically.
m
3. Press
. The display shows
ADD
?.
m
4. Press
again. The display shows
NAME
?.
m
5. Enter the name and press
. The number is displayed.
m
6. Edit the number if necessary, then press
.
u
d
7. Press
or
to select the ringer melody you want and press
The number is stored.
3.7.3
Delete an entry
r
1. Press
to open the Redial list.
p
u
d
2. Scroll
or
to the entry you want and press
. The display shows
m
p
3. Press
to confirm or
to cancel.
3.74
Delete the entire Redial list
r
1. Press
to open the Redial list.
p
2. Press and hold
. The display shows
DELETE ALL
?.
m
3. Press
to confirm or to cancel.
3.8
Lock / unlock the keypad
t
.
You can lock the keypad so that it cannot be operated accidentally while carrying it around.
NOTE
When the keypad is locked, you can still answer incoming calls and operate the handset as
normal during the call. When the call ends, the keypad lock comes on again.
*
1. Press and hold
.
icon is displayed.
2. To unlock the keypad, press any key on your handset. The display shows
*
3. Press
within 5 seconds.
3.9
Paging / Find handset
You can alert a handset user that they are wanted or locate a missing handset.
Paging calls cannot be answered by a handset.
1. Press
on the base. All handsets registered to the base will ring.
2. To stop the ringing, press
on the base again or press any button on the handset.
4. Phonebook
You can store up to 50 names and numbers in the phonebook. Names can be up to 12 characters
long and numbers up to 24 digits. You can also select different ringer melodies for the phonebook
entries.
Welcome...
to your new Motorola C1LB+ Digital Cordless Telephone!
•
All handsets are fully cordless for locating anywhere within range.
•
50 Name and Number phonebook.
•
Bright backlit display.
•
Speakerphone for hands-free conversations.
•
Caller ID shows you who's calling and see details of the last 40 callers in a Calls list.
•
Redial up to 10 of the last numbers called.
•
Register up to 5 handsets to a single base and register each handset with up to 4 different
bases.
•
Make internal calls and transfer external calls between handsets.
•
Choose from 10 different ringtones for internal and external calls as well as numbers stored in
the phonebook.
Please note that this equipment is not designed for making emergency telephone calls when
the power fails. Alternative arrangements should be made for access to emergency services.
Need help?
If you have any problems setting up or using your C1LB+, please contact Customer Services
on (65) 68412668. Email: [email protected].
Alternatively, you may find the answer in the 'Help' section at the back of this guide.
1
You must subscribe to your network provider's Caller ID or Call Waiting service for these
features to work. A subscription fee may be payable.
BATTERY PERFORMANCE
In ideal conditions, fully charged batteries should give up to 6.5 hours talk time or up to 135 hours
standby time on a single charge.
1
Note that new batteries do not reach their full capacity until they have been put to normal use for
several days.
To keep your batteries in the best condition, leave the handset off the base for a few hours at a
time.
Running the batteries right down at least once a week will help them last as long as possible.
The charge capacity of rechargeable batteries will reduce with time as they wear out, giving the
handset less talk / standby time. Eventually they will need to be replaced.
After charging your handset for the first time, subsequent charging time is about 6–8 hours a day.
Batteries and handset may become warm during charging. This is normal.
All talk and standby times are approximate and depend on features selected and usage
1
pattern.
Date and time
If you have subscribed to a Caller ID Service, the date and time is set automatically for all handsets
when you receive your first call.
If you do not have a Caller ID service, you can set the date and time manually, see section "7.
Clock & Alarm".
Your C1LB+ is now ready for use.
Menu map
PHONEBOOK
HANDSET
ADD ENTRY
BEEP
MODIFY ENTRY
INT RING VOL
DELETE ENTRY
EXT RING VOL
SETUP
INT MELODY
DEL HANDSET
EXT MELODY
PIN CODE
AUTO ANSWER
DIAL MODE
NAME
A
RECALL
LANGUAGE
DEFAULT
KEYLOCK ?
ECO MODE
3. Using the phone
NOTE
Your handset will automatically time the duration of all external calls. The call timer will display
after the first 15 seconds of your call. When the call ends, the total duration of your talk time is
shown for 5 seconds.
3.1
Switch the handset on / off
n
Press and hold
to switch the handset on or off.
3.2
Calls
3.2.1
Make a call
t
1. Press
.
2. When you hear the dial tone, dial the number.
3.2.2
Preparatory dialling
1. Dial the number first. If you make a mistake press
t
2. Press
to dial.
p
3.2.3
End a call
n
. To exit the
Press
, or place the handset back on the base or charger.
3.2.4
Receive a call
When you receive an external call, the phone rings and
1. If the handset is off the base then press
simply lift the handset to answer the call.
4.1
Store a name and number
If the C1LB+ is connected to a switchboard, you may need to enter a pause in a stored number.
This gives the switchboard time to find an outside line.
A pause is normally stored after the switchboard access code (e.g. 9).
When storing a number, press and hold
m
storing the phone number.
.
If you have subscribed to Caller ID Service and wish to display the name of your caller instead of
the number, save the full telephone number including the area code to your phonebook.
You can store multiple entries with the same number. However, to prevent unnecessary
duplicated entries, you can only store the same name once.
m
DELETE
?.
1. Press
. The display shows PHONEBOOK.
m
2. Press
. The display shows
ADD
m
3. Press
. The display shows
NAME
m
4. Enter the name and press
. The display shows
m
5. Enter the number and press
. The display shows
u
d
6. Press
or
to select the ringer melody you want and press
The display shows
ADD
ENTRY.
p
7. Enter the next name and number entry that you wish to store in your phonebook or press
twice to return to standby.
ENTERING NAMES
8
Use the keypad letters to enter names, e.g. to store TOM:
Press
once to enter T.
6
Press
three times to enter O.
6
PRESS
*.
Press
once to enter M.
p
WRITING TIPS
Press
to delete the last character or digit.
u
d
Press
or
to move between characters.
1
Press
to insert a space.
1
Use
twice to insert a dash.
4.2
View or dial an entry
p
1. Press
.
icon is displayed.
u
d
2. Scroll
or
to the entry you want.
OR
This user guide provides you with all the information you need to get
the most from your phone.
To set up your phone, follow the simple instructions in 'Getting
Started', on the next few pages.
IMPORTANT
Only use the telephone line cord supplied.
Got everything?
•
C1LB+ base & cordless handset
1
•
2 x rechargeable Ni-MH battery cells
•
Power adaptor for the base
•
Telephone line cord
If you have purchased a C1LB+ multiple pack you will also have the following additional
items:
•
Cordless handset & charger
•
2 x rechargeable Ni-MH battery cells
•
Power adaptor for the charger
ECOMOTO: a convergence of efforts by marketing, design, research, engineering and
supply chain management that leads to better products for everyone. A holistic view that
focuses on both social and environmental responsibility. A passion and a shared point of view.
The right thing to do.
•
Meets and / or exceeds EMEA environmental regulatory requirements.
•
Eco friendly packaging with a minimum 20% post consumer recycled content.
•
Phone housing is built with a minimum of 25% post consumer recycled content plastic.
•
Energy efficient charger that meets EU Code of Conduct requirements.
•
ECO mode function which reduces the transmitted power and energy consumption.
2. Getting to know your phone
Overview of your handset
Up
During a call, press to increase
earpiece volume.
When the phone is ringing,
press to increase the handset
ringer volume.
Press to scroll through the
menu options, redial list, calls
list and phonebook entries.
Menu / OK / Mute
Press to open the Menu.
Press to select menu
options and to con rm a
displayed option.
During a call, press to turn
mute on / o .
Talk / Hands-free
Press to make and receive
calls.
Press to switch hands-free
on or o during a call.
Keypad lock / * / Switch
from Pulse to Tone
Press and hold to lock the
keypad.
To unlock, press any key
and follow the on screen
instructions.
Dial a *.
During a call, press and
hold to switch from pulse
dialling to
tone dialling.
Recall
Use with switchboard / PABX
services and some network services.
When on an external call, press
Recall to get a fresh dialling tone or
to access call waiting when you hear
the signal. Press the key again to
toggle between your two callers.
NOTE
If you prefer to press
DATE -- TIME
Auto answer off.
DATE SET
3.3
Adjust the earpiece volume
CLOCK SET
During a call, press
ALARM SET
from.
REGISTER
3.4
Mute
SELECT BASE
You can mute your handset so that you can talk to someone nearby without your caller hearing.
REG BASE
1. During a call, press
m
2. Press
3.5
Intercom
3.5.1
Make an internal call
If you have more than one handset registered to the base, you can make internal calls between
two handsets.
icon is displayed to indicate an internal call.
I
1. Press
3.5.2
Receive an internal call
When you receive an internal call,
displayed.
t
1. Press
3.5.3
Transfer a call
You can transfer an external call to another handset registered to the base.
During an external call:
I
1. Press
p
2. When the other handset answers, press
to delete the last digit.
NOTE
If there is no answer from the other handset and you wish to return to your external caller,
I
press
.
Your external call resumes automatically after 30 seconds if there is no answer.
3.5.4
3-way conference call
icon flashes on the display.
t
You can hold a 3-way conference call between 2 internal callers and 1 external caller.
to answer the call, or if the handset is on the base
During a call with an external caller:
1. Press followed by the handset number (1-5) that you want to establish a conference call.
Enter the first letter of the name to search alphabetically.
The first name that starts with this letter or the nearest letter in the alphabet will be displayed.
u
Scroll
or
t
#
3. Press
until the display shows P. You can then continue
NOTE
When the name is displayed, you can switch between the name and number by pressing
4.3
Edit a name and number
m
1. Press
m
2. Press
d
3. Scroll
ENTRY.
u
4. Scroll
or
?.
existing name is displayed.
p
NUMBER
?.
5. Press
existing number is displayed.
MELODY
1.
p
m
6. Press
.
u
7. Scroll
or
8. Enter the next name and number entry you wish to store in your phonebook or press
twice to return to standby.
4.4
Delete an entry
m
1. Press
m
2. Press
d
3. Scroll
u
4. Scroll
or
display shows
m
5. Press
5. Handset settings
5.1
Handset ringer volume
You can adjust the ringer volume and set different volume levels for your internal and external
calls. Choose from 5 volume levels or Off.
m
1. Press
u
2. Press
or
u
3. Press
or
Display
Earpiece
Calls list / Down
In standby mode, press to open
the calls list.
During a call, press to decrease
earpiece volume.
When the phone is ringing, press
to decrease the handset ringer
volume.
Press to scroll through the menu
options, redial list, calls list and
phonebook entries.
Phonebook / Delete / Back
In standby mode, press to open
the phonebook menu.
In editing mode, press to delete
characters and digits.
Go back to the previous menu
level.
End Call / Exit / Switch Handset
on / o
Press to end a call.
When viewing the redial / calls
list / phonebook or when in the
menu, press to exit and return to
standby.
Press and hold for 3 seconds to
switch the handset on / o .
Pause / #
Press and hold to enter a
pause (P) when pre-dialling
or storing numbers.
Dial a #.
Microphone
Intercom
Redial
Used to make internal calls
In standby mode,
and transfer calls to other
press to open the
C1LB+ handsets registered
redial list.
to the base.
t
when you lift up the handset to answer a call, you will need to switch
u
d
or
to increase or decrease the volume. There are 5 levels to choose
m
. The display shows
MUTE
and your caller cannot hear you.
again to resume your call.
followed by the number (1-5) of the handset you want to call.
icon flashes and the handset number that is calling you is
to answer the call.
followed by the handset number (1-5) that you want to transfer to.
n
to complete the transfer.
d
to the entry you want.
n
to dial or
to return to standby.
m
. The display shows PHONEBOOK.
. The display shows
ADD
ENTRY.
m
to
MODIFY ENTRY
and press
.
m
d
to the entry you want to edit, or search alphabetically and press
. The
m
to delete the name if required, then enter the new name and press
. The
m
to delete the number if required, then enter the new number and press
.
m
d
to select a new ringer melody and press
. The display shows
ADD
ENTRY.
p
. The display shows PHONEBOOK.
. The display shows
ADD
ENTRY.
m
to
DELETE ENTRY
and press
.
m
d
to the entry you want to delete, or search alphabetically and press
. The
CONFIRM
?.
p
to confirm or
to cancel.
m
d
, scroll
to
HANDSET
and press
.
m
d
to select
INT RING VOL
or
EXT RING VOL
and press
.
d
to select the volume (1 -5 or OFF) .
.