Epson C11C524025 - FX 890 - Printer Manual de información del producto - Página 12
Navegue en línea o descargue pdf Manual de información del producto para Software Epson C11C524025 - FX 890 - Printer. Epson C11C524025 - FX 890 - Printer 19 páginas. Impact printers
También para Epson C11C524025 - FX 890 - Printer: Manual del usuario (48 páginas), Manual (11 páginas), Especificaciones (2 páginas), Resumen técnico (7 páginas)
Imprimir página
Using the Micro Adjust Function
The Micro Adjust function allows you to move the paper
forward or backward in 1/216-inch (0.118 mm) increments to
adjust the tear-off and top-of-form positions.
Adjusting the Tear-off Position
If your paper's perforation is not aligned with the tear-off edge,
you can use the Micro Adjust function to move the perforation
to the tear-off position. Your tear-off position setting remains in
effect until you change it, even if you turn off the printer.
Caution: Never use the knob to adjust the tear-off position; this may
damage the printer or cause it to lose the tear-off position.
1. Make sure the Tear Off/Bin light is flashing (the paper is at
the current tear-off position). You may need to press the
button to advance the paper to the tear-off
Tear Off/Bin
position.
2. Hold down the
Pause
Pause light begins flashing and the printer enters Micro
Adjust mode.
3. Open the paper guide cover and press
paper backward, or
Load/Eject
until the paper perforation is aligned with the tear-off edge
of the printer cover.
Note: The printer has a minimum and a maximum tear-off
position. If you try to adjust the position beyond these limits, the
printer beeps and stops moving the paper.
button for about three seconds. The
D to feed
LF/FF
U to feed paper forward,
tear-off edge
paper
perforation
4. Tear off the printed pages.
5. Press the
button to turn off Micro Adjust mode.
Pause
When you resume printing, the printer automatically feeds the
paper back to the top-of-form position and begins printing.
Adjusting the Top-of-form Position
The top-of-form position is the position on the page where the
printer starts printing. If your printing appears too high or low
on the page, you can use the Micro Adjust function to adjust
the top-of-form position, as described below. Your top-of-form
position setting remains in effect until you change it, even if you
turn off the printer.
Caution: Never use the knob to adjust the top-of-form position; this
may damage the printer or cause it to lose the top-of-form position.
1. Make sure the printer is turned on.
2. Load paper. (If the tractor is in a push position, press the
button to advance continuous paper to the
Load/Eject
current top-of-form position.) If necessary, lift up the
printer cover so you can see the paper position.
3. Hold down the
Pause
light flashes and the printer enters Micro Adjust mode.
4. Press the
D button to move the top-of-form position
LF/FF
up on the page, or press the
the top-of-form position down on the page.
5. Press the
button to exit Micro Adjust mode.
Pause
Note: The printer has a minimum and a maximum top-of-form
position. If you try to adjust it beyond these limits, the printer
beeps and stops moving the paper.
When the paper reaches the default top-of-form position, the
printer beeps and stops moving the paper briefly. You can use
this setting as a reference point when adjusting the position.
The top margin setting made in some software overrides the
top-of-form position setting you make with the Micro Adjust
function.
6/03
EPSON FX-890/FX-2190
button for three seconds. The Pause
U button to move
Load/Eject
EPSON FX-890/FX-2190
11
-