Dimplex 6905050100-500 Manual de servicio - Página 10

Navegue en línea o descargue pdf Manual de servicio para Chimenea de interior Dimplex 6905050100-500. Dimplex 6905050100-500 18 páginas.

Imprimir página

Dimplex 6905050100-500 Manual de servicio

ing so that they will not be pinched when re-attaching

the bottom panel.

14. Insert new bulbs.

15. Re-assemble the firebox in reverse order.

NOTE: Ensure the rear tab/ledge on the log-set/ember-

bed is installed tightly under the bottom of the partially

reflective glass to prevent light leakage.

MOD B

Tools required: Phillips head screw driver

Small wire cutter

CAUTION: Follow "Preparation for Service" instructions

before proceeding.

1. Carefully turn the firebox onto its back so that the bot-

tom can be easily accessed.

2. Remove the 9 screws that attach the bottom panel to

the side panels, 2 on the back side, 2 on the left side,

2 on the right side and 3 on the bottom along the front

edge. (Figure 7)

3. Locate the LED light assembly and remove the 4

screws securing the assembly to the two side panels.

4. Remove the light assembly wire ends out of the termi-

nal block by removing the small Philips head screw in

the 2 respective terminals.

5. Insert the wire ends from the new light assembly into

the terminal block following the same orientation of the

original wires.

6. Install the new LED light assembly back into the unit.

7. Re-assemble the firebox in reverse order.

NOTE: Ensure that when reinstalling the bottom panel

of the firebox that no wires are pinched.

Figure 7

LED Light

Assembly

FLICKER MOTOR/FLICKER ROD

REPLACEMENT

Tools Required: Phillips head screw driver

before proceeding.

1. Slightly wedge your fingers between the back partially

ember-bed, not the logs themselves.

may be necessary to remove.

decorative glass pieces as an ember bed, remove the glass

pieces then remove the plastic media tray following the

same method as the log set removal instructions.

2. Set log set or media tray aside in a safe location.

3. Disconnect flicker rod from the motor by slightly bend-

damage the rod. Ensure the rod is straight after re-instal-

lation so that it doesn't affect the operation of the flicker

effect.

4. Carefully turn the firebox upside down so that the bot-

5. Remove the 9 screws that attach the bottom panel to

6. Remove the 3 flicker motor wire ends out of the termi-

terminals that hold the flicker motor wires on the terminal

block. Take note of the terminal locations and the wire

configuration.

7. Using a Philips screwdriver (a short screwdriver is

8. Place the new motor into the housing and attach the

Terminal Block

9. Insert the 3 wire ends from the new flicker motor as

10. Tighten terminal screws to secure wires in place.

CAUTION: Follow "Preparation for Service" instructions

reflective glass and the log-set/ember-bed on either

the right or left side. Pull the back edge of the plastic

ember bed forward until the rear tab/ledge clears past

the bottom of the partially reflective glass and pull the

log set forward and out.

IMPORTANT: Only handle the log-set by the plastic

NOTE: Log-set fits tightly into firebox. Some force

NOTE: If your model has the media tray with the

ing the flicker rod and pulling the rubber gasket off the

motor shaft. (Figure 3).

NOTE: Be careful not to bend the rod. Doing so may

tom panel is facing up.

the side panels, 2 on the back side, 2 on the left side,

2 on the right side and 3 on the bottom along the front

edge.

nal block by removing the small Philips head screw in

the 3 respective terminals. Take note of their location

on the terminal block.

NOTE: A capacitor is also connected in 2 of the 3

recommended), remove the 2 screws holding the flicker

motor to the mounting brackets. One screw on either

side and remove the flicker motor out of the housing.

Take note of the orientation on the brackets.

motor to the brackets using the 2 Philips screws.

well as the 2 wires from the original capacitor into the

terminal block following the orientation of the original

motor & capacitor. (See Assembly Part Pictures)