Toshiba XE30U - TLP XGA LCD Projector Manual del usuario - Página 22

Navegue en línea o descargue pdf Manual del usuario para Proyector Toshiba XE30U - TLP XGA LCD Projector. Toshiba XE30U - TLP XGA LCD Projector 28 páginas. Mobile projector
También para Toshiba XE30U - TLP XGA LCD Projector: Especificaciones (2 páginas), Especificaciones detalladas (2 páginas)

Imprimir página
Toshiba XE30U - TLP XGA LCD Projector Manual del usuario
Using the menus (Continued)

■ Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.
Item
Description
Projector
Input
Input source name
Mode name
RGB input mode
[Note 1]
Resolution
Resolution (in dots)
Frequency
Sync frequency
Sync
Sync signal polarity
[Note 2]
Signal format
Y/P
/P
signal format
B
R
Video mode
Color method of video signal
Lamp time
Time of lamp use
[Note 3]
Lamp reset count The count for lamp replacement
Total time
The total time that this projector
is used.
Version
Firmware version
[Note 4]
Notes
1: The mode of supported RGB signals
p.51
2: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as
a counter of guaranteed lamp time.) Please replace the lamp after 2000 hours of use if [Lamp
power] is set to [Standard], or after 3000 hours of use if [Lamp power] is set to [Low], consult
with a dealer about getting replacement for lamp TLPLW11 (sold separately).
4: [Version] shows the version of the projector's internal control program. This firmware version
will be requested for customer service purposes.
Note
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
"Yes": displayed, "No": not displayed
Computer Y/P
/P
Video S-video
B
R
Yes
Yes
Yes
Yes
No
No
Yes
No
No
Yes
No
No
Yes
No
No
No
Yes
No
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
is shown.
42

Maintenance

About lamp

The product's light source is a mercury lamp that lights at increased internal pressure. Be sure
to fully understand the following characteristics of the lamp and handle it with extreme care.
• The lamp may burst with a loud noise due to impact or deterioration, or fail to light at
the expiration of its life.
• How long it takes before the lamp bursts or the life expires may vary greatly by lamp.
Some may burst shortly after first use.
• Burst is likely to happen if the lamp is used after the replacement period has elapsed.
• When the lamp bursts, the broken pieces of glass may get inside the product or be
Yes
released outside from the openings for ventilation.
No
• When the lamp bursts, a slight amount of mercury gas enclosed in the lamp along with
No
glass dust may be released from the openings for ventilation.
No
■ Immediately replace the lamp when a replacement message
No
appears on the screen.
No
Yes
• When the replacement time approaches, a message will appear on the screen.
Yes
• The risk of burst will increase if the lamp is continuously used without being replaced.
Yes
• Frequently check the used hours and prepare spares when the replacement time
approaches. (Refer to "Status display".
Yes
■ When the lamp is broken
Yes
• If glass components, including a lamp and a lens, should break, handle the broken
pieces with care to avoid injury and contact your dealer for repair service.
• In the event of lamp burst, unplug the product from the wall outlet, leave and completely
ventilate the room. Then, thoroughly clean the area around the projector and discard
any edible items placed in that area, as they may be contaminated.
• If the lamp bursts, consult a doctor if glass dust or mercury gas gets into your eyes or is
inhaled.
)
p.42
43