AEO E-power 5A 2S Instrucciones - Página 2

Navegue en línea o descargue pdf Instrucciones para Motor AEO E-power 5A 2S. AEO E-power 5A 2S 2 páginas. Brushless motor esc

Imprimir página

Introduction

1.All devices are original and genuine, ensuring that the ESC is of the highest quality and high

reliability.

2. It can withstand a higher current.

3. It can set the throttle stroke, compatible with a variety of remote control .With smooth and

delicate feel of speed control,first-class linear speed regulation.

4. The maximum speed can be reached 210,000 RPM (2-pole motor), 70,000 RPM (6-pole motor)

and 35,000 RPM (12-pole motor).

•Thank you for purchasing this product. It is strongly recommended that you read

this manual carefully before using the device and strictly comply with the specified

operating procedures. We are not responsible for any liability arising from the use

of this product.

Note: This manual is not suitable for E-power 5A (1S/2S)

Function

1. The type of battery: Lithium battery / NI-MH battery

2. Battery low voltage protection mode: limit the throttle to only 40% when the voltage reaches low voltage protection.

3. Advance angle: divided into low, medium and high.

In general, the low advance Angle can accommodate more motors. However, as the motor structure is quite different, please try each advance

Angle to get a satisfactory driving effect. In order to improve the speed, the advance Angle can be set as the high advance Angle. After

changing the approach Angle, it is recommended to test on the ground before flying.

Setting Instruction

Using your brushless ESC for the first time

Please pay attention! In order to adapt the ESC to your remote control throttle stroke, the throttle stroke should be resetting for the first time when using this ESC

or changing other remote controls, so as to get the best linear throttle.

Setting instructions of throttle stroke

Turn on the

remote

control,then adjust

the throttle to the

highest point.

The lowest voice

"♫123" from ESC

indicates the

throttle to be the

lowest.

Instruction of Normal Boot

Turn on the remote

control,then adjust

the throttle to the

lowest point.

Programming instructions for using the remote control

Turn on the remote

control,then adjust

the throttle to the

highest point.

After hearing a certain

function sound, pull

down the throttle and

♫45

sound "

" to select

this function.

The highest voice

Connect the ESC to

"bi-bi" from ESC

the battery and

indicates the throttle

wait for 2 seconds.

to be the highest.

The system is

ready to take off.

The ESC is powered

The prompt "♫123"

by a short beep to

indicates that the

indicate the number

normal system is

of lithium battery

ready for power-on.

segments.

The ESC issued the

Connect the ESC

"Bi-Bi-" indicate the

to the battery and

throttle to be the

wait for 2 seconds.

highest.

After completing the selection,

push up the throttle to

continue the function setting,

and drop down the throttle to

exit the setting.

Instructions for Brushless Motor ESC

Push the throttle to

the lowest and wait

for 1 second.

Push the throttle to

take off at any time.

Wait for about 4

seconds, the beep

sound "

means to enter the

function settings.

Function 1: Automatically detect the number of lithium batteries,

and set the protection voltage according to the number of detected

lithium batteries(each lithium battery protection voltage 2.8V)

Function 2: Protect 2 lithium batteries

Function 3: Protect 3 lithium batteries

Function 4: Low advance angle

Function 5: Medium advance angle

Function 6: High advance angle

Function 7: Restore factory defaults

Factory default setting: automatic detection of the number of

lithium batteries, low advance angle.

The sound of short

beep indicates the

number of lithium

battery protection.

Loops 1-7 sounds,

♫12345

corresponding to 1-7

function settings.