Pioneer DEH-2750 Manual de instalación

Navegue en línea o descargue pdf Manual de instalación para Receptor para automóvil Pioneer DEH-2750. Pioneer DEH-2750 5 páginas. Car radio

Imprimir página

DEH-2850MP

DEH-1850

This product conforms to new cord colors.

Los colores de los cables de este producto se

conforman con un nuevo código de colores.

As cores dos fios deste produto seguem um novo

padrão de cores.

Æ...b¹b'« „öÝô« Ê«

uÃ« lÄ "UN'« «c¼ r− M¹

Printed in Thailand

<CRD4030-A/N> ES

60°

Fig. 1

Fig. 3

± qJAÃ«

≥ qJAÃ«

182

Fig. 2

Fig. 4

¥ qJAÃ«

≤ qJAÃ«

Fig. 5

Fig. 7

∑ qJAÃ«

µ qJAÃ«

Fig. 6

∂ qJAÃ«

Installation

Note:

Removing the Unit (Fig. 3) (Fig. 4)

•

Before making a final installation of the unit,

5. Frame

temporarily connect the wiring to confirm that

To remove the frame, extend top and bottom of

the connections are correct and the system works

the frame outwards in order to unlock it. (When

properly.

reattaching the frame, point the side with a

•

Use only the parts included with the unit to

groove downwards and attach it.)

ensure proper installation. The use of unautho-

• It becomes easy to remove the frame if the front

rized parts can cause malfunctions.

panel is released.

•

Consult with your nearest dealer if installation

6. Insert the supplied extraction keys into the unit,

requires the drilling of holes or other modifica-

as shown in the figure, until they click into place.

tions of the vehicle.

Keeping the keys pressed against the sides of the

•

Install the unit where it does not get in the dri-

unit, pull the unit out.

ver's way and cannot injure the passenger if there

is a sudden stop, like an emergency stop.

DIN Rear-mount

•

The semiconductor laser will be damaged if it

overheats, so don't install the unit anywhere hot

— for instance, near a heater outlet.

Installation using the screw holes on

•

If installation angle exceeds 60° from horizontal,

the side of the unit (Fig. 5) (Fig. 6) (Fig. 7)

the unit might not give its optimum performance.

(Fig. 1)

1. Remove the frame.

•

When installing, to ensure proper heat dispersal

7. Frame

when using this unit, make sure you leave ample

space behind the rear panel and wrap any loose

To remove the frame, extend top and bottom of

cables so they are not blocking the vents.

the frame outwards in order to unlock it. (When

reattaching the frame, point the side with a

groove downwards and attach it.)

DIN Front/Rear-mount

• It becomes easy to remove the frame if the front

panel is released.

This unit can be properly installed either from

"Front" (conventional DIN Front-mount) or

2. Fastening the unit to the factory

"Rear" (DIN Rear-mount installation, utilizing

radio mounting bracket.

threaded screw holes at the sides of unit chassis).

8. Select a position where the screw holes of the

For details, refer to the following illustrated

bracket and the screw holes of the head unit

installation methods.

become aligned (are fitted), and tighten the

screws at 2 places on each side. Use either truss

screws (5 × 8 mm) or flush surface screws

DIN Front-mount

(5 × 9 mm), depending on the shape of the screw

holes in the bracket.

Installation with the rubber bush (Fig. 2)

9. Screw

1. Dashboard

10. Factory radio mounting bracket

2. Holder

11. Dashboard or Console

After inserting the holder into the dashboard,

then select the appropriate tabs according to the

thickness of the dashboard material and bend

them.

(Install as firmly as possible using the top and

bottom tabs. To secure, bend the tabs 90

degrees.)

3. Rubber bush

4. Screw