Pioneer MVH-X580DAB Manual del usuario - Página 22
Navegue en línea o descargue pdf Manual del usuario para Receptor para automóvil Pioneer MVH-X580DAB. Pioneer MVH-X580DAB 28 páginas.
Imprimir página
Blue/white
Connect to the system control terminal
of the power amp (max. 300 mA 12 V
DC).
Blue/white
Connect to the auto-antenna relay
control terminal (max. 300 mA 12 V DC).
Speaker leads
White: Front left
(STD) or high range
left
(NW)
White/black: Front left
(STD) or high
range left
(NW)
Gray: Front right
(STD) or high range
right
(NW)
Gray/black: Front right
(STD) or high
range right
(NW)
Green: Rear left
(STD) or middle
range left
(NW)
Green/black: Rear left
(STD) or
middle range left
(NW)
Violet: Rear right
(STD) or middle
range right
(NW)
Violet/black: Rear right
(STD) or
middle range right
(NW)
Orange/white
Connect to a car's illumination signal.
ISO connector
In some vehicles, the ISO connector
may be divided into two. In this case, be
sure to connect to both connectors.
NOTES
• Change the initial menu of this unit. Refer
to [REAR-SP] (page 5). The subwoofer
output of this unit is monaural.
• When using a subwoofer of 2 Ω, be sure
to connect the subwoofer to the violet
and violet/black leads of this unit. Do not
connect anything to the green and
green/black leads.
Power amp (sold separately)
Perform these connections when using the
optional amplifier.
System remote control
Connect to blue/white cable.
Power amp (sold separately)
Connect with RCA cables (sold
separately)
To rear output (STD) or middle range
output (NW)
Rear speaker (STD) or middle range
speaker (NW)
To front output (STD) or high range
output (NW)
Front speaker (STD) or high range
speaker (NW)
To subwoofer output
Subwoofer
Installation
Important
• Check all connections and systems before
final installation.
• Do not use unauthorized parts as this
may cause malfunctions.
• Consult your dealer if installation requires
drilling of holes or other modifications to
the vehicle.
• Do not install this unit where:
– it may interfere with operation of the
vehicle.
– it may cause injury to a passenger as a
result of a sudden stop.
Autogoods "130"
• The semiconductor laser will be damaged
if it overheats. Install this unit away from
hot places such as near the heater outlet.
• Optimum performance is
obtained when the unit is
installed at an angle of less
than 60°.
• When installing, to ensure proper heat
dispersal when using this unit, make sure
you leave ample space behind the rear
panel and wrap any loose cables so they
are not blocking the vents.
Leave ample
5 cm
space
5 cm
DIN mount installation
1
Insert the supplied mounting sleeve
into the dashboard.
2
Secure the mounting sleeve by using a
screwdriver to bend the metal tabs
(90°) into place.
Dashboard
Mounting sleeve
• Make sure that the unit is installed
securely in place. An unstable
installation may cause skipping or
other malfunctions.
When not using the supplied
mounting sleeve
1
Determine the appropriate position
where the holes on the bracket and
the side of the unit match.
2
Tighten two screws on each side.
Tapping screw (5 mm × 9 mm, not
supplied with product)
Mounting bracket
Dashboard or console
Removing the unit (installed with
the supplied mounting sleeve)
1
Remove the trim ring.
Trim ring
Notched tab
• Releasing the front panel allows easier
access to the trim ring.
• When reattaching the trim ring, point
the side with the notched tab down.
2
Insert the supplied extraction keys
into both sides of the unit until they
click into place.
3
Pull the unit out of the dashboard.
En
21