Pioneer Super Tuner III D DEH-P2550 Manual de instalación

Navegue en línea o descargue pdf Manual de instalación para Receptor para automóvil Pioneer Super Tuner III D DEH-P2550. Pioneer Super Tuner III D DEH-P2550 6 páginas. Audio system

Imprimir página

DEH-P2550

This product conforms to new cord colors.

Los colores de los cables de este producto se

conforman con un nuevo código de colores.

As cores dos fios deste produto seguem um novo

padrão de cores.

Æ...b¹b'« „öÝô« Ê«

uÃ« lÄ "UN'« «c¼ r− M¹

Printed in China

<CRD3692-A/U> ES

60°

Fig. 1

Fig. 3

± qJAÃ«

≥ qJAÃ«

182

Fig. 2

Fig. 4

≤ qJAÃ«

¥ qJAÃ«

Fig. 5

Fig. 7

∑ qJAÃ«

µ qJAÃ«

Fig. 6

∂ qJAÃ«

Installation

Note:

Removing the Unit (Fig. 3) (Fig. 4)

•

Before finally installing the unit, connect the

5. Frame

wiring temporarily, making sure it is all connect-

6. Insert the release pin into the hole in the bottom

ed up properly, and the unit and the system work

of the frame and pull out to remove the frame.

properly.

(When reattaching the frame, point the side with

•

Use only the parts included with the unit to

a groove downwards and attach it.)

ensure proper installation. The use of unautho-

7. Insert the supplied extraction keys into the unit,

rized parts can cause malfunctions.

as shown in the figure, until they click into place.

•

Consult with your nearest dealer if installation

Keeping the keys pressed against the sides of the

requires the drilling of holes or other modifica-

unit, pull the unit out.

tions of the vehicle.

•

Install the unit where it does not get in the dri-

DIN Rear-mount

ver's way and cannot injure the passenger if there

is a sudden stop, like an emergency stop.

•

The semiconductor laser will be damaged if it

Installation using the screw holes on

overheats, so don't install the unit anywhere hot

the side of the unit (Fig. 5) (Fig. 6) (Fig. 7)

— for instance, near a heater outlet.

•

If installation angle exceeds 60° from horizontal,

1. Remove the frame.

the unit might not give its optimum performance.

8. Frame

(Fig. 1)

9. Insert the release pin into the hole in the bottom

of the frame and pull out to remove the frame.

DIN Front/Rear-mount

(When reattaching the frame, point the side with

a groove downwards and attach it.)

This unit can be properly installed either from

2. Fastening the unit to the factory

"Front" (conventional DIN Front-mount) or

"Rear" (DIN Rear-mount installation, utilizing

radio mounting bracket.

threaded screw holes at the sides of unit chassis).

10. Select a position where the screw holes of the

For details, refer to the following illustrated

bracket and the screw holes of the head unit

installation methods.

become aligned (are fitted), and tighten the

screws at 2 places on each side. Use either truss

screws (5 × 8 mm) or flush surface screws

DIN Front-mount

(5 × 9 mm), depending on the shape of the screw

holes in the bracket.

Installation with the rubber bush (Fig. 2)

11. Screw

1. Dashboard

12. Factory radio mounting bracket

2. Holder

13. Dashboard or Console

After inserting the holder into the dashboard,

then select the appropriate tabs according to the

thickness of the dashboard material and bend

them.

(Install as firmly as possible using the top and

bottom tabs. To secure, bend the tabs 90

degrees.)

3. Rubber bush

4. Screw