Pioneer XV-DV360 Puesta en marcha

Navegue en línea o descargue pdf Puesta en marcha para Receptor para automóvil Pioneer XV-DV360. Pioneer XV-DV360 2 páginas. 5.1 home theater system with usb* connection for jpeg “slideshow with music”
También para Pioneer XV-DV360: Manual de instrucciones (48 páginas), Especificaciones (2 páginas)

Imprimir página

Setting up your DVD/CD Receiver

When connecting this system or changing connections, be sure to switch the power off with the STANDBY/ON button, and disconnect the power cord from the AC outlet.

Do not use these speakers with any other system or amplifier as this may result in damage or fire.

Check that you have all the accessories, then put

the batteries in the remote control.

Power cord

Remote control

STANDBY

TUNER

/ON

DVD/CD

(FM/AM)

Video cord

OPEN/

USB

LINE

AUDIO

SUBTITLE

ANGLE

ZOOM

CLEAR

DISPLAY

FM antenna

TOP MENU

TUNE

AA size IEC R6

ENTER

HOME

dry cell batteries

RETURN

TUNE

SETUP

TEST TONE

SURROUND

SOUND

(to confirm

system operation)

TV CONTROL

SLEEP

INPUT

CHANNEL

VOLUME

MUTE

VOLUME

AM loop antenna

Connect each speaker using the color-coded speaker cords.

Match them to the colored speaker terminals on the rear

panel of the DVD/CD receiver.

COMPONENT

FRONT

VIDEO

LINE

DEO

SURROUND

VIDEO OUT

AUDIO IN

For the best surround sound, setup your speakers

as above. The front left and right speakers should

be about 6 ft to 9 ft apart.

These speaker terminals carry HAZARDOUS LIVE voltage. To prevent the risk of

electric shock when connecting or disconnecting the speaker cables, disconnect

the power cord before touching any uninsulated parts.

Speaker Setup Guide

Check that you have all the speaker accessories.

• Front speakers x 2

• Center speaker x 1

• Speaker cords x 6

Front left (White)

Surround left (Blue)

Standard surround 5-spot setup

This is a standard multichannel

surround sound speaker setup for

optimal 5.1 channel home theater

sound.

Surround

left

Attach the smaller non-skid pads to the base of each of the front,

surround and center speakers. The four large non-skid pads are

for the subwoofer (as shown).

Use the supplied adhesive to attach 4 pads to the base (flat surface) of each speaker.

Center speaker

Front and surround speakers

Connect the speaker system.

Refer to the Setting up your DVD/CD Receiver (the other part of this setup guide) to

connect the speakers properly. Place them as shown in the diagram above for optimal

surround sound.

Make sure the Front Surround mode is switched off.

See the operating instructions for more on using Front Surround.

Connect the AM and FM antennas to the rear panel of the DVD/CD receiver.

Pull off the protective

shields of both AM antenna

wires.

Push open the tabs, then insert

one wire fully into each terminal.

Release the tabs to secure the AM

antenna wires.

Fix the AM loop antenna to the

attached stand.

To fix the stand to the antenna, bend in the

direction indicated by the arrow (fig. A) then

clip the loop onto the stand (fig. B).

Note: If you plan to mount the AM antenna

to a wall or other surface, secure the stand

with screws (fig. C) before clipping the loop

to the stand. Make sure the reception is clear.

Place the AM antenna on a flat

surface and point in the direction

giving the best reception.

Don't let it come into contact with metal

objects and avoid placing near computers,

television sets or other electrical appliances.

Surround right

(Grey)

CENTER

Listening position

SUB

WOOFER

SPEAKERS

Center (Green)

• Subwoofer x 1

• Surround speakers x 2

Front right (Red)

Surround right (Grey)

Wall mounting the speakers

All the speakers (except the subwoofer, which should be placed

on the ground) have mounting holes, and depending on the

speaker setup you choose, you can wall-mount the front, center

Subwoofer

and (5-spot setup only) surround speakers.

Front left

Front right

Center

Surround

right

Listening position

0.2 in. to 0.28 in.

Before mounting (see above), keep in mind the following points:

• Remember that the speaker system is heavy and that its

weight could cause the screws to work loose, or the wall

material to fail to support it, resulting in the speaker falling.

Make sure that the wall you intend to mount the speakers on is

strong enough to support them. Do not mount on plywood or

soft surface walls.

• Mounting screws are not supplied. Use screws suitable for the

Subwoofer

wall material and support the weight of the speaker.

• If you are unsure of the qualities and strength of the walls,

consult a professional for advice.

• Pioneer is not responsible for any accidents or damage that

result from improper installation.

fig. A

fig. B

ANTENNA

fig. C

AM LOOP

UNBAL 75Ω

Connect the FM wire antenna to the FM UNBAL 75 Ω antenna terminal.

For best results, extend the FM antenna fully and fix to a wall or door

frame. Don't drape loosely or leave coiled up.

The signal earth (H) is designed to reduce noise that occurs when an

Note:

antenna is connected. It is not an electrical safety earth.

Connect each speaker as shown below.

Surround left

(Blue)

Color-coded connector

(Connect to rear panel)

Twist and pull off the protective

shields on each wire.

Connect the wires to the

speaker. Match the colored

wire with the color-coded

label (above the tabs), then

insert the colored wire into

Subwoofer (Purple)

the red (+) tab and the other

wire with the black (–) tab.

Connect the other end to the

color-coded speaker terminals

on the rear of the DVD/CD

receiver (as shown at left).

Make sure to insert completely.

Upper three terminals

The small lug at the wire-end of

Front left

the speaker plug should face up

(White)

or down depending on whether

it's being plugged into one of

the upper or lower three

speaker terminals. Please make

Lower three terminals

sure to connect correctly.

• Speaker stands x 2

• Non-skid pads

(large) x 4

• Non-skid pads

(small) x 20

• Screws x 2

Center (Green)

Subwoofer (Purple)

0.2 in.

0.4 in.

Caution

Using the remote control

The remote control can be used within a range of about

23 feet from the remote sensor on the front panel, and

within a 30 degree angle.

Precautions:

• The remote control may not work if there is an obstacle

between the remote control and the display unit, or if the

remote control is not directed towards the remote sensor

of the display unit at the correct angle.

• The remote control may not work properly if strong

light such as direct sunlight or fluorescent light is shining

onto the unit's remote sensor.

• The remote control may not work properly when this

unit is used near devices emitting infrared rays, or when

remote controls of other devices which use infrared rays

are used. Also, the use of this remote control may cause

other devices to work improperly.

• When the operating range of the remote becomes too

short, replace the batteries.

Remote control battery caution

Incorrect use of batteries may cause leakage or

rupture.

Always be sure to follow these guidelines:

• Always insert batteries into the battery compartment

correctly matching the positive ª and negative ·

polarities, as shown by the display inside the

compartment.

• Never mix new and used batteries.

• Batteries of the same size may have different voltages,

depending on brand. Do not mix different brands of

batteries.

• When disposing of used batteries, please comply with

governmental regulations or environmental public

instruction's rules that apply in your country or area.

• In order to prevent battery leakage, remove the

batteries when not using the remote control for an

extended period (one month or more). If leakage occurs,

carefully wipe away any battery fluid inside the

compartment, and replace the batteries with new ones.

• Do not allow books or other objects to rest on top of

the remote control, since the buttons may be depressed,

causing faster exhaustion of the batteries.

• Do not use or store batteries in direct sunlight or

excessively hot places, such as inside a car or near a heater.

This can cause batteries to leak, overheat, explode or catch

fire. It can also reduce the life or performance of batteries.

Color-coded wire

Connect the DVD/CD receiver to your TV, then connect the

(Connect to speaker)

supplied power cord.

Connect one end to a video input on your TV.

Use the supplied video cord.

Connect the other end to the video output of the DVD/CD receiver.

This player is equipped with copy protection technology. Do not connect this

player to your TV via a VCR using AV cables, as the picture from this player will not

appear properly on your TV.

Connect the power cord to the AC inlet.

ANTENNA

COMPONENT

VIDEO

AM LOOP

UNBAL 75 Ω

S-VIDEO

HDMI OUT

VIDEO OUT

HDMI OUT

Congratulations! You're done setting up.

Printed in

Front surround

3-spot setup

This setup is ideal when rear surround

speaker placement isn't possible or

you want to avoid running long

speaker cables in your listening area.

Attach the smaller

non-skid pads to the

base of the front

and center speakers

and to the speaker

stands. The four

Front speakers

large non-skid pads

are for the

subwoofer.

Use the supplied adhesive

to attach 4 pads to the

base (flat surface) of each

speaker or stand.

Attach the surround speakers to

the speaker stands.

For each speaker, line up the spurs on the

stand with the holes on the back of the

speaker and insert, then secure the speaker

to the stand with the screw provided.

Connect the speaker system.

Refer to the Setting up your DVD/CD Receiver (the other part of this setup guide) to

connect the speakers properly. Place them as shown in the diagram above for optimal

surround sound.

Turn the speakers as shown, following the guide marks for optimal

Front Surround.

Turn each surround speaker so that the guide markers on the stand base are lined up

horizontally in the direction the listening position (see below). This is only necessary

when you are using the Front Surround mode (MODE ON). See the operating

instructions for more on using Front Surround.

Additional notes on connecting antennas

• Keep antenna cables away from the main unit and other cables.

• To assure optimum reception, pull the FM antenna so that it is

fully extended and not coiled or hanging at the rear of the unit.

• If reception with the supplied antenna is poor, see the Other

connections section in the main operating instructions for details

on connecting outdoor antennas.

Additional notes on speaker placement

If your listening room is of adequate size, place the speakers as

shown in step 3 to achieve the optimum surround sound effect. If

you are listening in a fairly small room and a typical surround

speaker setup is not possible, see Home theater sound setup in the

instruction manual and the Speaker Setup Guide for information on

the Front Surround 3-spot setup option.

When using the standard surround speaker setup as shown in

step 3, please observe the following guidelines:

• Install the main front left and right speakers at an equal

distance from the TV.

• For optimum effect, place the rear speakers slightly above ear

level.

• Install the center speaker above or below the TV so that the

sound of the center channel is localized at the TV screen.

Precautions:

• When installing the center speaker on top of the TV, be sure to

secure it with tape or some other suitable means. Otherwise, the

speaker may fall from the TV due to external shocks such as

earthquakes, endangering those nearby or damaging the speaker.

• Do not connect the supplied speakers with any other amplifier.

This may result in malfunction or fire.

• Make sure that all the bare speaker wire is twisted together

and inserted fully into the speaker terminal. If any of the bare

speaker wire touches the back panel it may cause the power to

cut off as a safety measure.

• The front, center and surround speakers supplied with this

system are magnetically shielded. However, depending on the

installation location, color distortion may occur if the speaker is

installed extremely close to the screen of a television set. If this

happens case, turn the power switch of the television set OFF, and

turn it ON after 15 min to 30 min. If the problem persists, place

the speaker system away from the television set.

• The subwoofer is not magnetically shielded and so should not

be placed near a TV or monitor. Magnetic storage media (such as

floppy discs and tape or video cassettes) should also not be kept

close to the subwoofer.

• Do not attach the subwoofer to the wall or ceiling. They may

fall off and cause injury.

VIDEO IN

VIDEO

LINE

FRONT

CENTER

AC IN

SUB

SURROUND

WOOFER

AUDIO IN

SPEAKERS

AC IN

To AC outlet

Imprimé au

<ARE7604-A>

Surround

Subwoofer

Surround

left

right

Center

Front left

Front right

Listening position

Center speaker

Subwoofer

Speaker stand

Caution

• Please don't attach the

surround speakers to the wall for

the Front surround 3-spot setup.