Pioneer A-509R Manual de instrucciones - Página 7

Navegue en línea o descargue pdf Manual de instrucciones para Amplificador Pioneer A-509R. Pioneer A-509R 12 páginas.
También para Pioneer A-509R: Manual de servicio (30 páginas)

Imprimir página

REC SELECTOR switch /indicator(For TAPE 1/CD-

R/MD terminals)

This switch is used to select the recording source compo-

nent. The signal from the selected component is output at

the TAPE1/CD-R/MD jacks for recording. To select a record-

ing source component, press the REC SELECTOR switch so

that the indicator of the desired source component lights

up. When this switch is set to [TUNER] or [CD], the signal

from the selected component can be recorded regardless

of the input selector switch and TAPE2 MONITOR button

settings.

: To record from the equipment connected to the

CD terminals.

TUNER : To record from the equipment connected to the

TUNER terminals.

SOURCE : To record from the equipment selected by the

INPUT SELECTOR knob.

OFF

: In this position, nothing from the REC terminals

of TAPE 1/CD-R/MD is output. Set to this posi-

tion when not recording; the cassette deck will

be disconnected, improving sound quality.

NOTE:

The function selected using the INPUT SELECTOR knob will

be recorded irrespective of the position of the REC SELEC-

TOR switch (TAPE 2 MONITOR terminals).

BALANCE control

Should normally be left in the center position. Adjust the

balance if the sound is louder from one of the speakers. If

the right side is louder, turn toward the L (left) position and

if the left side is louder, turn toward the R (right) position.

NOTE:

This control does not operate at DIRECT ON mode.

DIRECT/SB MODE button/indicator

Press and hold the button for more than 3 seconds to switch

SB mode ON. (Volume indicator goes out)

Press and hold the button for more than 3 seconds again to

switch SB mode OFF. (Volume indicator lights)

[DIRECT]

Use this button when you do not wish to pass the output

from input terminal equipment through the various fre-

quency adjusting circuits (BASS, TREBLE, BALANCE, LOUD-

NESS).

On : The indicator lights. The signals input through the

input terminals are reproduced without passing

through the various frequency adjusting circuits. This

results in flat, pure sound which is a more faithful

reproduction of the input source.

Off : The indicator goes out. The signal passes through

the various frequency adjusting circuits.

[SB MODE]

The SB mode is a special mode in which the amplifier does

not accept remote control except power ON/OFF (But all of

the facilities can be controled by manual as same as SB mode

OFF.). Fix the VOLUME control near the center position. In

this mode, the set can be used as a power amplifier which

amplifies the LINE/SURROUND BACK input (the function

name is LINE/SB) with a input sensitivity of 1 V.

For example, when the set is combined with one of Pioneer's

Surround Back compatible receiver, the set can be used as

the Surround Back amplifier.

(For details, please refer to the instruction manual of the

receiver.)

LOUDNESS button/indicator

Use when listening at low volume level.

On : The indicator lights. Boosts low and high frequen-

cies to give added punch to playback even at low

volume level.

Off : The indicator goes out. Should normally be left in

this position.

NOTE:

This button does not operate at DIRECT ON mode.

TREBLE tone control

Use to adjust the high-frequency tone. The center position is

the flat (normal) position. When turned to the right, the high-

frequency tone is emphasized; when turned to the left, the

high-frequency tone is de-emphasized.

NOTE:

This control does not operate at DIRECT ON mode.

BASS tone control

Use to adjust the low-frequency tone. The center position is

the flat (normal) position. When turned to the right, the low-

frequency tone is emphasized; when turned to the left, the

low-frequency tone is de-emphasized.

NOTE:

This control does not operate at DIRECT ON mode.

PHONES jack

When using headphones, insert the plug into this jack.

SPEAKERS B (ON/OFF) button/indicator

Use this button to listen to the speaker system connected to

the SPEAKERS B terminals.

On : The indicator lights. Sound is heard from the speaker

system.

Off : The indicator goes out. No sound is heard from the

speaker system. Set to this position when listening

with headphones.

SPEAKERS A (ON/OFF) button/indicator

Use this button to listen to the speaker system connected to

the SPEAKERS A terminals.

On : The indicator lights. Sound is heard from the speaker

system.

Off : The indicator goes out. No sound is heard from the

speaker system. Set to this position when listening

with headphones.

PANEL FACILITIES