Pioneer PRS-D400 Manual del usuario - Página 9
Navegue en línea o descargue pdf Manual del usuario para Amplificador Pioneer PRS-D400. Pioneer PRS-D400 12 páginas. Bridgeable four-channel power amplifier
También para Pioneer PRS-D400: Manual de servicio (37 páginas)
Imprimir página
MAN-PRS-D400-GB.fm Page 9 Tuesday, February 21, 2006 3:43 PM
Installation
Example of installation on the floor mat or on the
chassis
1. Place the amplifier where it is to be installed. Insert the supplied tapping screws
(4 x 18 mm) into the screw holes. Push on the screws with a screwdriver so they
make marks where the installation holes are to be located.
2. Drill 2.5 mm diameter holes at the point marked, and install the amplifier, either
on the carpet or directly to the chassis.
Replacing the terminal cover
1. Align the unit and terminal cover, and insert the screw.
2. Tighten the screw with a 4 mm hexagonal wrench.
Screw
Tapping screws (4 x 18 mm)
Terminal Cover
Floor mat or chassis
Drill a 2.5 mm diameter hole
Specifications
Power source .......................................................................... 14.4 V DC (10.8 V to 15.1 V allowable)
Grounding system .......................................................................................................... Negative type
Current consumption ...................................................................... 27.7 A (at continuous power, 4 Ω)
Average current drawn* ......................................................................... 10.4 A (4 Ω for four channels)
Fuse ......................................................................................................................................... 30 A x 2
Dimensions ......................................................................................... 304 (W) x 56 (H) x 202 (D) mm
Weight ....................................................................................... 3.0 kg (Leads for wiring not included)
Maximum power output .................................................................. 150 W x 4 (4 Ω) / 600 W x 2 (4 Ω)
Continuous power output ................................. 75 W x 4 (at 14.4 V, 4 Ω, 20 Hz to 20 kHz 1.0% THD)
Load impedance .......................................................................................... 4 Ω (2 Ω to 8 Ω allowable)
Frequency response ........................................................................... 10 Hz to 40 kHz (+0 dB, –3 dB)
Signal-to-noise ratio ........................................................................................ 100 dB (IEC-A network)
Distortion .......................................................................................................... 0.005 % (10 W, 1 kHz)
Separation ...................................................................................................................... 70 dB (1 kHz)
Low pass filter ................................................................................ Cut off frequency: 40 Hz to 120 Hz
High pass filter ............................................................................... Cut off frequency: 40 Hz to 120 Hz
Gain control ....................................................................................................... RCA: 400 mV to 6.5 V
Maximum input level / impedance .......................................................................... RCA: 6.5 V / 22 kΩ
Note:
• Specifications and the design are subject to possible modification without notice due to
improvements.
* Average current drawn
The average current drawn is nearly the maximum current drawn by this unit when an audio
signal is input. Use this value when working out total current drawn by multiple power
amplifiers.
20.2 A (4 Ω for two channels)
20.2 A (2 Ω for four channels)
300 W x 2 (at 14.4 V, 4 Ω, 1 kHz 1.0% THD)
150 W x 4 (at 14.4 V, 2 Ω, 1 kHz 1.0% THD)
(Bridge connection: 4 Ω to 8 Ω allowable)
Cut off slope: –12 dB/oct
Cut off slope: –12 dB/oct
Speaker: 1.6 V to 26 V
Speaker: 26 V / 90 kΩ
9