Pioneer DVD-A02 Manual de servicio - Página 30

Navegue en línea o descargue pdf Manual de servicio para Reproductor de DVD Pioneer DVD-A02. Pioneer DVD-A02 31 páginas. Dvd-rom drive unit
También para Pioneer DVD-A02: Manual de instrucciones (37 páginas)

Imprimir página
Pioneer DVD-A02 Manual de servicio
DVD-102, DVD-A02

8. PANEL FACILITIES AND SPECIFICATIONS

PANEL FACILITIES
÷ ÷ ÷ ÷ ÷ FRONT VIEW
DVD-ROM
DRIVE
7
PHONES
5
6
1 Disc loading slot
Insert the DVD-ROM or CD-ROM with the label facing up.
Precautions on Playing 8 cm/3-inch Discs
¶ When playing 8 cm/3-inch discs, always use the
adapter for 8 cm/3-inch discs. Before loading the disc
into the DVD-ROM drive unit, be sure to check that it
is secured properly by the catches of the adapter. If
discs have been inserted without the adapter by
mistake, remove the disc immediately by pressing the
eject button. If the disc does not come out with one
press, press another time.
¶ Use 8 cm/3-inch disc adapters labeled with the
mark (recommended standard product). Do not use
adapters which cause the disc to idle, nor adapters
which are bent or curved.
2 Eject (0) button
This button is used to eject the disc.
3 BUSY indicator
Flashes during data access.
4 DVD indicator
Lights when a DVD is loaded.
5 Volume Control (headphone level)
This is used to adjust the volume level of the
headphone jack.
6 Headphone jack (PHONES)
This is a stereo minijack for headphones.
7 Hole for forced ejection
When the eject button has lost its function, insert an
accessory pin for emergency ejection into this hole
and push to eject the disc.
WARNING:
÷ Before executing this operation, be sure to switch off
the powe supply of the computer and confirm that the
disc loading is stopped.
It takes approx. 30 seconds to stop loading a disc after
switching off the power supply.
÷ Always use the pin provided (Do not use other objects).
30
for DVD-A02
BUSY
DVD
4
3
2
'
REAR VIEW
1
4
1
5
=
-
9 DC Input
This is the power supply input for DC +5 V and +12 V.
Pin
Name
1
+12
Power supply input for DC +12 V.
2
G
Ground.
3
G
Ground.
4
+5
Power supply input for DC +5 V.
Host IDE Interface
10
This is a 40 pin I/O connector according to the ATA
specifications.
Device Configuration Jumper
11
This is the jumper switch for selection of the drive use
mode and supporting PC.
Short-circuit socket is attached for the setting
attached : on
Pin
Name
1
1
MA*
on The drive is used in master mode.
2
SL
on The drive is used in slave mode.
3
CS
on Mode for drive setting by CSEL of the
IDE interface.
4
Reserved
5
RPC on Stay in RPC Phase l mode
Start RPC Phase ll mode (Never
SET*
1
off return to Phase l mode after Phase ll
2
*
mode is used.)
1
*
Pin 1 (MA) and Pin 5 (PRC SET) are ON at the time of shipping from
the plant.
*
2
For a DVD Video playback system (computer) for Phase l, please
use with Phase l. When the DVD VideoÅ playback system (compu-
ter) and the drive have different region codes, DVD Video playback
is not possible.
Set the jumper switch to OFF only when use of a drive correspond-
ing to Phase ll has been specified clearly for the DVD Video play-
back system (computer). DVD-102 will be initalzed automatically
and will operate in Phase ll mode.
= Audio Output (AUDIO OUT)
This is a connector for output of analog audio.
As a Molex 70553 type connector is used,select a
match-ing connection cable.
Pin
Name
1
L
Left channel audio output.
2
G
Ground.
3
G
Ground.
4
R
Right channel audio output.
39
1
1
40
2
4
0
9
Function
not attached : off
Function
Function
1