Pioneer XDV-P6 - DVD Changer - in-dash Manual de instalación

Navegue en línea o descargue pdf Manual de instalación para Reproductor de DVD Pioneer XDV-P6 - DVD Changer - in-dash. Pioneer XDV-P6 - DVD Changer - in-dash 9 páginas. Other manual
También para Pioneer XDV-P6 - DVD Changer - in-dash: Manual de instalación (5 páginas)

Imprimir página

XDV-P6

This product conforms to CEMA cord colors.

Le code de couleur des câbles utilisé pour ce produit est

conforme à CEMA.

Printed in Japan

Imprimé au Japon

<CRD4109-A> UC

Connecting the Units

WARNING:

CAUTION:

• To avoid the risk of accident and the

• PIONEER does not recommend that you

potential violation of applicable laws, the

install or service your display (sold sepa-

front DVD or TV (sold separately) fea-

rately) yourself. Installing or servicing

ture should never be used while the vehi-

the product may expose you to risk of

cle is being driven. Also, Rear Displays

electric shock or other hazards. Refer all

should not be in a location where it is a

installation and servicing of your display

visible distraction to the driver.

to authorized Pioneer service personnel.

• In some countries or states the viewing of

• Secure all wiring with cable clamps or

images on a display inside a vehicle even

electrical tape. Do not allow any bare

by persons other than the driver may be

wiring to remain exposed.

illegal. Where such regulations apply,

• Do not drill a hole into the engine com-

they must be obeyed and this unit's DVD

partment to connect the yellow lead of

features should not be used.

the unit to the vehicle battery. Engine

vibration may eventually cause the insu-

lation to fail at the point where the wire

passes from the passenger compartment

into the engine compartment. Take extra

care in securing the wire at this point.

• It is extremely dangerous to allow the

display (sold separately) lead to become

wound around the steering column or

gearshift. Be sure to install the display in

such a way that it will not obstruct dri-

ving.

• Make sure that wires will not interfere

with moving parts of the vehicle, such as

the gearshift, parking brake or seat slid-

ing mechanism.

• Do not shorten any leads. If you do, the

protection circuit may fail to work prop-

erly.

• Do not install the display (sold sepa-

rately) where it may (i) obstruct the

driver's vision, (ii) impair the perfor-

mance of any of the vehicle's operat-

ing systems or safety features, includ-

ing air bags, hazard lamp buttons or

(iii) impair the driver's ability to

safely operate the vehicle.

Note:

• This unit cannot be installed in a vehicle that

• This unit is for vehicles with a 12-volt battery and

does not have an ACC (accessory) position on

negative grounding. Before installing it in a recre-

the ignition switch.

ational vehicle, truck, or bus, check the battery

voltage.

• To avoid shorts in the electrical system, be sure to

disconnect the ≠ battery cable before beginning

installation.

• Refer to the owner's manual for details on

connecting the power amp and other units, then

make connections correctly.

• Secure the wiring with cable clamps or adhesive

ACC position

No ACC position

tape. To protect the wiring, wrap adhesive tape

around them where they lie against metal parts.

• The black lead is ground. Please ground this lead

• Route and secure all wiring so it cannot touch any

separately from the ground of high-current prod-

moving parts, such as the gear shift, handbrake and

ucts such as power amps.

seat rails. Do not route wiring in places that get

If you ground the products together and the ground

hot, such as near the heater outlet. If the insulation

becomes detached, there is a risk of damage to the

of the wiring melts or gets torn, there is a danger of

products or fire.

the wiring short-circuiting to the vehicle body.

• Don't pass the yellow lead through a hole into the

engine compartment to connect to the battery. This

• Cords for this product and those for other prod-

will damage the lead insulation and cause a very

ucts may be different colors even if they have

dangerous short.

the same function. When connecting this product

• Do not shorten any leads. If you do, the protection

circuit may fail to work when it should.

to another product, refer to the supplied manuals

• Never feed power to other equipment by cutting

of both products and connect cords that have the

same function.

the insulation of the power supply lead of the unit

and tapping into the lead. The current capacity of

the lead will be exceeded, causing overheating.

• When replacing the fuse, be sure to only use a fuse

of the rating prescribed on the fuse holder.

• To prevent incorrect connection, the input side of

the IP-BUS connector is blue, and the output side

is black. Connect the connectors of the same colors

correctly.