Pioneer PDP505CMX - HD Plasma Display Manual de servicio - Página 3
Navegue en línea o descargue pdf Manual de servicio para Monitor Pioneer PDP505CMX - HD Plasma Display. Pioneer PDP505CMX - HD Plasma Display 23 páginas. 50-inch wxga professional plasma display
También para Pioneer PDP505CMX - HD Plasma Display: Manual de referencia de comandos (23 páginas), Folleto y especificaciones (8 páginas)
Imprimir página
5
QQ
3 7 63 1515 0
Leakage Current Cold Check
With the AC plug removed from an AC power source, place a
jumper across the two plug prongs. Turn the AC power switch on.
Using an insulation tester (DC 500V), connect one lead to the
jumpered AC plug and touch the other lead to each exposed metal
part (input/output terminals, screwheads, metal overlays, control
shafts, etc.), particularly any exposed metal part having a return
path to the chassis. Exposed metal parts having a return path to
the chassis should have a minimum resistor reading of 0.3MΩ
and a maximum resistor reading of 5MΩ. Any resistor value
below or above this range indicates an abnormality which
requires corrective action. Exposed metal parts not having a
return path to the chassis will indicate an open circuit.
Leakage Current Hot Check
Plug the AC line cord directly into an AC power source (do not
use an isolation transformer for this check).
Turn the AC power switch on.
U s i n g a " L e a k a g e C u r r e n t Te s t e r ( S i m p s o n M o d e l 2 2 9
equivalent)", measure for current from all exposed metal parts of
the cabinet (input/output terminals, screwheads, metal overlays,
control shaft, etc.), particularly any exposed metal part having a
return path to the chassis, to a known earth ground (water pipe,
conduit, etc.). Any current measured must not exceed 0.5mA.
TE
L 13942296513
Device
under
test
Also test with
plug reversed
(Using AC adapter
plug as required)
A N Y M E A S U R E M E N T S N O T W I T H I N T H E L I M I T S
OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL
SHOCK HAZARD AND MUST BE CORRECTED BEFORE
RETURNING THE SET TO THE CUSTOMER.
www
.
5
http://www.xiaoyu163.com
Reading should
not be above
Leakage
0.5mA
current
tester
Test all
exposed metal
surfaces
Earth
ground
AC Leakage Test
x
ao
y
i
http://www.xiaoyu163.com
6
8
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in PIONEER set have
special safety related characteristics. These are often not evident
from visual inspection nor the protection afforded by them
necessarily can be obtained by using replacement components
rated for higher voltage, wattage, etc. Replacement parts which
have these special safety characteristics are identified in this
Service Manual.
Electrical components having such features are identified by
marking with a
Service Manual.
The use of a substitute replacement component which dose not
h a v e t h e s a m e s a f e t y c h a r a c t e r i s t i c s a s t h e P I O N E E R
recommended replacement one, shown in the parts list in this
Service Manual, may create shock, fire or other hazards.
Product Safety is continuously under review and new instructions
are issued from time to time. For the latest information, always
consult the current PIONEER Service Manual. A subscription to,
or additional copies of, PIONEER Service Manual may be
obtained at a nominal charge from PIONEER.
Q Q
3
6 7
1 3
u163
.
PDP-505CMX
6
7
2 9
9 4
2 8
on the schematics and on the parts list in this
1 5
0 5
8
2 9
9 4
m
co
7
8
9 9
A
B
2 8
9 9
C
D
3
8