Ariston LI 700 I-S Manual de uso y mantenimiento - Página 6

Navegue en línea o descargue pdf Manual de uso y mantenimiento para Lavavajillas Ariston LI 700 I-S. Ariston LI 700 I-S 36 páginas. Ariston care and use manual dishwasher li 700 i-sli 700 i-s
También para Ariston LI 700 I-S: Manual de uso y mantenimiento (36 páginas)

Imprimir página
Starting the dishwasher
Ready, steady, go!
You have loaded your dishes and you now have to set
the wash cycle. It takes just one minute to learn how
After
performing
all the
operations described in the
previous paragraphs
press
on-off button "A": indicator
light "B" comes on.
Selecting the wash cycle,
To select
the wash cycle
press button "P". Each time
you press
the button,
a
beep
will
sound
and
indicator lights "E" will light
up in sequence: choose the
cycle
you
deem
most
suited to the type of dishes
to be washed (have a look
at the wash cycle table on
page 7). If the appliance
door is shut, press the Start
button "R" and you will hear
a beep; the cycle will start
up within a few seconds.
The dishwasher keeps you
informed.
Your dishwasher
is fitted
with
indicator
lights
(G)
which light up to indicate
the cycle phase under way.
prewash,wash,rinsing,
drying.
At all times,
your
dishwasher
tells you which
cycle phase is under way.
Modifying a wash cycle in
progress.
If you
have
chosen
the
wrong cycle, not to worry!
You can modify the wash
cycle in progress,
if it has
only just started.
Keep the RESET
button
"R" pressed
for about
5
seconds: a prolonged beep
wilt sound,
followed
by
three short beeps. Indicator
light "G" will turn offand at
this stage, all the settings
wilt have been cancelled.
You are now free to re-set
the correct wash cycle.
You've left out a dish?
Well,
it
happens
to
everyone.
Interrupt
the
wash cycle by pressing the
ON-OFF button, insert the
dish you had forgotten and
press the ON-OFF
button
again. The cycle will start
up
from
where
you
interrupted
it.
Finished?
The end of the wash cycle
is indicated
by two short
beeps and the flashing of
the drying phase indicator
light.
The end of the wash cycle
is indicated
by two short
beeps and the flashing of
the drying phase indicator
light.
•Turn the appliance
off by
pressing
button "A", thus
cutting
off the electricity
supply.
• If accessible
turn off the
water tap
• Wait
a few
minutes
before
unloading
the
dishes: they are very hot!
If you wait a little while,
they dry better thanks
to
the steam.
Empty
the
lower
rack
first.
There's
been
a power
failure? Have you opened
the dishwasher door?
The wash cycle stops and
then
restarts
when
the
electricity
comes back on
or when you shut the door.
Everything
is
under
control!
If opening
the door
soon after
the end of
the program, or during
it, stand away from the
Dishwasher, to avoid
possible injury from
hot steam.
You decide when it starts.
When you have loaded the
dishes,
you can choose
when
to
start
your
dishwasher
before setting
the wash
cycle
desired.
Press button "D" to delay
the start of the wash cycle
by 12, 9, 6 or 3 hours.
Each time you press it, you
will hear a short beep and
the
indicator
light
"G"
corresponding
to
the
selected delay wilt light up.
Now you can select
the
desired wash cycle. Press
the start
button
"R" and
after you hear the beep, the
countdown
to the delayed
start wilt begin.
Once this time is up, the
indicator
light
will
stop
flashing and the wash cycle
will begin.
If you have set a 12 hour
delay, for example,
once
you
have
selected
the
wash cycle,
the 12 hour
indicator
light
will flash
followed
by the others
in
sequence until the set time
delay is up. A quick look at
the indicator lights will keep
you
informed
of
the
countdown
progress
at all
times.
Have you changed
your
mind?
If you change
your mind,
you can set a shorter time
delay: press button "D" to
select it. You need not reset
the wash cycle.
If on the other hand you
want to cancel the delay
set and you want the
cycle to start immediately,
press button "D"
repeatedly until the cycle
starts and indicator light
"G" corresponding
to the
cycle start phase comes
on.
Dual function
of indicator
lights "G"
1) flashing
to indicate a
delayed
start: to remind
you that you have set a
delayed start;
2) on and not flashing
beneath
the cycle phase
symbol:
meaning
the cycle
has
started and is in the phase
indicated by the symbol.
You want to wash on the
upper rack only?
Remember to use half the
amount of detergent.
Your
dishwasher
also
allows you to wash half a
load,
to save water
and
electricity.
Before
setting
any wash
cycle
whatsoever,
press
button
"F" to select
that
you want to run a half cycle
on the upper rack.
When you press it, you wilt
hear a beep and indicator
light "H" corresponding
to
the selected
function
will
come on.
Would you like to see which
settings you have made?
At any
time,
when
the
cycle is under way, if you
press button "P", the cycle
in progress
indicator
light
will
light
up for
a few
seconds,
followed
by the
half load
indicator
light,
wherever
set.
www.aristonappliances.us
ARISTON DISHWASHER - User Manual
5