Whirlpool 2DLSQ7533JQ4 Instrucciones de instalación - Página 4

Navegue en línea o descargue pdf Instrucciones de instalación para Lavadora Whirlpool 2DLSQ7533JQ4. Whirlpool 2DLSQ7533JQ4 5 páginas.

Imprimir página

Drain hose

connection:

Inlet hose

connection:

(to water faucets)

Leveling

washer:

Securing

drain hose:

Panel C

IMPORTANT: THIS PROCEDURE

MUST BE FOLLOWED TO

ASSURE PROPER

INSTALLATION.

drain

hose

clamp

ribbed

stop

1/4"

(0.64 cm)

To prevent the drain hose

from coming off or leaking,

it must be installed per the

following instructions.

• Wet the inside end of the drain

hose with tap water. DO NOT

USE ANY OTHER LUBRICANT.

• Squeeze ears of drain hose clamp

with pliers to open and place

clamp over the end of the drain

hose.

Check inlet hoses

periodically. Replace inlet

hoses if you find bulges,

kinks, cuts, wear or leaking.

Replace inlet hoses after

hot

five years of use.

11.

Stack two corner posts

on top of each other.

Tilt washer backwards and slide

corner posts under washer 3

inches (7.6 cm) from each side

of washer as shown.

1/2"

(1.3 cm)

base

nut

12.

Screw nut down on

legs to within 1/2 inch

(1.3 cm) of base.

NOTE: Use shipping strap to

secure drain hose. Water pressure

could cause drain hose to come

out of standpipe or laundry tub if

drain hose is not secured.

about 16"

(40.6 cm)

17.

After shipping strap has been

removed (Step 1), look for the

words "cut here" marked on the

shipping strap, about 16 inches

(40.6 cm) from plug end.

Cut the shipping strap at this

mark. Pull shipping strap out of

the power supply cord.

• Open clamp and push end of drain

hose onto drain connector until

hose contacts ribbed stop.

• Place clamp over area marked

"clamp". Release clamp.

Standpipe or

laundry tub

drain system: Open

yellow clamp and slide

over "hook" end of

drain hose to secure

the rubber and

corrugated

sections together.

If drain hose does

not fit into standpipe

or is being placed over

the edge of a laundry

tub, open other hose

clamp with pliers and

place clamp over rigid

end of drain hose.

Insert end of hose

extension into rigid end of drain hose up

to stops on the sides of hose extension.

Secure with clamp.

Floor drain system: Do Not install

"hook" end of drain hose to

corrugated section. Consult your

plumber for proper installation.

Inlets are plastic.

Do Not strip or

crossthread.

cold

13.

Insert legs into correct

holes at each front corner of washer

until nuts touch washer. DO NOT

tighten nuts until Step 16.

14.

Tilt washer backward and

remove corner posts.

Gently lower washer to floor.

Move washer to its final

location. Remove cardboard or

hardboard from under washer.

Check that hose is not twisted

or kinked and is securely in

place.

strap

Put "hook" end of drain hose in

laundry tub or standpipe. Tightly

wrap the shipping strap around the

drain hose and laundry tub or

standpipe as shown in Figures A-B.

Push plug into the nearest hole in

the shipping strap.

If the water inlet faucets and drain

standpipe are recessed, put "hook"

end of drain hose in standpipe.

Tightly wrap the shipping strap

around the drain hose and faucet

body (not the handles or stems) as

shown in Figure C. Push plug into

the nearest hole in the shipping

strap.

Run water

through

both faucets into

a bucket to get

rid of particles in the water lines

that might clog hoses. Mark the hot

water faucet.

Put "hook" end of drain

hose into laundry tub or

standpipe. Check for proper length

of drain hose.

To prevent drain water from

going back into washer:

• Do Not straighten "hook"

end of drain hose and force

excess drain hose into

standpipe.

• Do Not lay excess drain hose

in bottom of laundry tub.

10.

Attach bottom hose from

the inlet marked "H" to

cold water

the hot water faucet. Attach top

inlet valve

hose from the inlet marked "C" to

hot water

the cold water faucet. Tighten

inlet valve

couplings to faucets. DO NOT

OVERTIGHTEN; this could cause

damage to couplings.

15.

Tilt washer forward

slightly so that back legs

are about 1 inch (2.5 cm) off floor.

Drop washer to floor. Check

levelness of the washer by placing a

carpenter's level on top of the

washer, first side to side; then front

to back.

16.

If washer is not level, repeat Step

11, and adjust the front legs up or

down. Then repeat Steps 14 & 15.

When washer is level, use

wrench to turn nuts on front

legs up tightly against washer

base. If nuts are not tight

against washer base, the

washer may vibrate.

strap

If a longer drain hose is needed, use

a 21" (53.3 cm) or 54" (137.1 cm)

drain hose and Connector Kit, Part

No. 285442. If drain hose must be

shortened, use Connector Kit Part

No. 285442. These parts are

available from your local dealer or

authorized parts distributor.

Note: If washer is moved to

adjust drain hose, the washer

must be leveled again. Repeat

Steps 15-16. Place cardboard

under the washer and carefully

move washer to avoid

damaging floor covering.