Whirlpool 2DLSQ8000JQ5 Manual de uso y mantenimiento - Página 9
Navegue en línea o descargue pdf Manual de uso y mantenimiento para Lavadora Whirlpool 2DLSQ8000JQ5. Whirlpool 2DLSQ8000JQ5 12 páginas. 120-volt 60-hz washer
También para Whirlpool 2DLSQ8000JQ5: Instrucciones de instalación (5 páginas)
Imprimir página
Replace inlet h oses a fter f iveyears o fusetoreduce t herisk of
hose failure. Periodically inspect and replace i nlet h oses i f
bulges, kinks, cuts, w ear o rleaks a refound.
When r eplacing your i nlet h oses, mark thedate ofreplacement
onthelabel witha permanent marker.
Install andstore your w asher where i twill n otfreeze. Because
some water m ay stay inthehoses, freezing candamage your
washer. Ifstoring o rmoving y our w asher during freezing weather,
winterize it.
Non-use
or vacation
care
Operate your washer only when you are at home. If you will be on
vacation or not using your washer for an extended period of time,
you should:
•
Unplug washer or disconnect
power.
•
Turn off the water supply to the washer. This helps avoid
accidental flooding (due to a water pressure surge) while you
are away.
To winterize
washer
1. Shut off both water faucets.
2. Disconnect and drain water inlet hoses.
3. Put 1 quart (1 L) of R.kL-type antifreeze in the basket.
4. Run washer on a drain and spin setting (see "Drain and Spin")
for about 30 seconds to mix the antifreeze and water.
5. Unplug washer or disconnect
power.
To use washer
again
1. Flush water pipes and hoses.
2. Reconnect water inlet hoses.
3. Turn on both water faucets.
4. Plug in washer or reconnect power.
5. Run the washer through a complete cycle with 1 cup (250 mL)
of detergent to clean out antifreeze.
TROUBLESHOOTING
First try the solutions
suggested
here and possibly avoid
the cost of a service
call...
Washer won't fill, rinse or agitate
•
Checkthe
following:
Is the power cord plugged in?
Is the indicator on the Cycle Control knob properly lined up
with a cycle? Turn the Cycle Control knob to the right slightly
and pull to start.
Are the water inlet valve screens clogged?
Are both the hot and cold water faucets turned on?
Is the water inlet hose kinked?
Does the water level seem too low, or does the washer
appear to not fill completely?
The top of the agitator is much higher than the highest water
level. This creates a perception that the washer is not filling
completely. This is normal.
Washer stops
•
Checkthe
following:
Is the power cord plugged in?
Is the indicator on the Cycle Control knob properly lined up
with a cycle? Turn the Cycle Control knob to the right slightly
and pull to start.
Are the water inlet valve screens clogged?
Are both the hot and cold water faucets turned on?
Is the water inlet hose kinked?
•
Is there power at the plug?
Check your electrical source or call an electrician.
•
Has a fuse blown or is the circuit
breaker open?
If problem continues, call an electrician.
•
Are you using an extension
cord?
Do not use an extension cord.
•
Is the washer in a normal pause in the Permanent
Press
(or Hand Washables)
cycle?
The washer pauses for about 2 minutes in the Permanent
Press cycle. Allow the cycle to continue.
The Hand Washables cycle (on some models) features
periods of agitation and soak.
•
Is the washer overloaded?
Wash smaller loads.
Washer won't drain or spin
•
Is the drain hose clogged,
or the end of the drain hose
more than 72 inches (183 cm) above the floor?
See the Installation Instructions for proper installation of drain
hose.
•
Is the lid open?
The lid must be closed during operation.
•
Is there excessive
sudsing?
Always measure detergent. Follow manufacturer's directions.
If you have very soft water, you might need to use less
detergent.
•
Is your voltage low?
Check your electrical source or call an electrician.
Do not use
an extension cord.
Washer continues to fill or drain, or the cycle seems stuck
•
Is the top of drain hose lower than the water level in
washer?
The top of the hose must be higher than the water level in the
washer for proper operation. See the Installation Instructions.
•
Does the drain hose fit too tightly in the standpipe,
or is it
taped to the standpipe?
The drain hose should be loose yet fit securely. Do not seal
the drain hose with tape. The hose needs an air gap. See the
Installation Instructions.