Whirlpool ADG 3550 WH Manual de consulta rápida - Página 3
Navegue en línea o descargue pdf Manual de consulta rápida para Lavadora Whirlpool ADG 3550 WH. Whirlpool ADG 3550 WH 4 páginas.
Imprimir página
Tips and advice
• Arrange crockery so that items do not
touch each other. Arrange large
crockery in the lower rack and smaller
crockery in the upper rack.
• Load cups at an angle to facilitate
water drainage.
• In general, place the cutlery in the
basket with the handles positioned
downwards. but ensure that sharp
knives and forks that might cause injury
are placed in the basket with the
handles positioned upwards.
• Make sure the water jet can reach all
loaded items and that the spray arms
turn freely.
Important
• Fill the detergent dispenser and check
the salt and rinse aid level.
• Do not use the appliance for items not
suitable for washing in a dishwasher,
for example. wooden items, aluminium,
plastic utensils, tin, hand-decorated
crockery (unglazed), silver cutlery.
• Do not put liquid fat in the dishwasher
(e.g. oil used for frying) or candle wax.
• If a fault occurs or you wish to change the
current programme,
press the "START" button for about 5
seconds until the Start indicator lamp
switches off.
• If regeneration salt is to be added
immediately start a wash programme
in order to eliminate any residual salt
(rinsing alone is not sufficient).
• Sometimes even when the
regeneration salt container is full, the
corresponding indicator lamp may
illuminate during the first wash cycle.
• Before starting a wash programme,
make sure that the spray arms can turn
freely and are not impeded by crockery
or cutlery.
• Switch off the dishwasher once the
"Start" indicator lamp has switched off.
If you switch off the dishwasher during
a wash cycle, when switched on again
the dishwasher resumes the cycle from
where it was interrupted without having
to start it again.
If a fault occurs, before contacting our
After-Sales Service, make the following
checks to try and remedy the problem:
The dishwasher is not working:
•
Is the plug properly inserted in the wall
socket?
•
Is there a power failure?
•
Is the dishwasher switched on?
•
Has the Start button been pressed?
•
Has the delayed start timer been set (if fitted).
•
Is the water supply tap on?
•
Is the flow of water obstructed by
impurities? If so, close the water supply tap,
detach the water hose and clean the filter.
Then re-connect the water hose to the tap
and open the water tap once again.
•
Are the filters clogged? (See "Care and
maintenance" chapter in the user
instructions).
•
Is the door closed properly?
•
Is a fault indicated?
(The Start indicator lamp flashes).
Start the programme again from the
beginning: press the Start button for
about 5 seconds, until the Start indicator
lamp switches off.
Select a new programme and press the
Start button.
Please read the user instructions carefully.
Troubleshooting Guide
Crockery still dirty after washing:
•
Was the crockery loaded properly?
•
Crockery must be loaded facing
downwards; make sure, especially for
large crockery.
•
The water jets must spray the entire
surface of all items.
•
Make sure that crockery and cutlery are
arranged properly.
•
Have you selected the correct
programme?
•
Did you use too much or too little
detergent? (The use of poor quality
detergents result in less effective
washing).
•
Are the filters clogged or incorrectly
assembled? (See "Care and
Maintenance" chapter in the user
instructions).
•
Are the spray arms blocked or the nozzles
clogged? (See "Care and Maintenance"
chapter in the user instructions).
•
Is the lower spray arm correctly fitted?
•
Is the salt container cap (water softening
system) screwed down?
Marked crockery:
•
Is the water hardness level selector not
properly adjusted? See ("Filling the salt
container" in the user instructions).
•
Is the salt container empty? (See "Filling
the salt container" in the user
instructions).
•
Was insufficient detergent used? (See
"Filling the detergent dispenser" in the
user instructions).
Marked glasses and cutlery:
•
Was too much rinse aid used? (See
"Filling the rinse aid dispenser" in the user
instructions).
Note: with some models, when the Start
button is pressed a pre-wash cycle precedes
the actual wash programme; this
regenerates the water softening system.
AFTER-SALES
SERVICE
If, after carrying out the above checks.
the fault persists or reoccurs, switch
off the appliance and close the water
tap. then contact our After-Sales
Service (see warranty).
Please specify:
•
The nature of the fault.
•
The appliance type and model.
•
The service code (the number indicated
after the word Service on the adhesive
rating plate) inside the door on
the right-hand side.
•
Your full address and telephone
number.