Whirlpool AWE 7516 Cuadro de programas - Página 2
Navegue en línea o descargue pdf Cuadro de programas para Lavadora Whirlpool AWE 7516. Whirlpool AWE 7516 2 páginas.
Imprimir página
CONSUMPTION DATA
Temperature
Programme
(°C)
Cotton
95
Cotton**
60
Cotton
40
Synthetics
60
Synthetics
40
Delicates
40
Daily load
40
Quick wash
30
Wool
40
Handwash
40
Prewash cycle increases programme duration by aproximately 20 min. Consumption values were measured in normalized conditions in
compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to
the water supply pressure and temperature, the load and the type of wash.
*
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water
out.
** Reference Programme for Energy Label.
*** The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions
applicable at that time.
PREPARATION OF THE WASH CYCLE
1. Load the machine, close the drum doors and check
that they are properly locked.
2. Add detergent and additives into the dispenser to
no more than the "MAX" level mark, as follows:
• Programme with pre and main wash
• Main wash programme without prewash
• Fabric softeners and conditioners
• Stain remover agents
• Anti-scale agents (if necessary)
3. Close the lid.
4. Turn the programme selector to the desired
programme and temperature. The time display shows
the duration of the chosen programme (in hours
and minutes), and the lamp next to the "Start/Pause"
button flashes. The indication lamp of the predefined
spin speed lights up.
SELECT THE DESIRED OPTION(S)
Selecting or deselecting an option can be done at
any time during the programme. The option will be
applied as long as the corresponding programme
phase has not been executed yet.
"Half load" button
• Reduces water consumption, above all during rinsing.
• Suitable for lightly soiled laundry and small loads
(max. 3 kg).
"Eco" button
• With a modified temperature profile and a slightly
prologned washing duration, the optimum
combination of excellent washing result and even
lower energy consumption is achieved.
Load
Water
Energy
Approx. Programme
Duration***
(kg)
(l)
(kWh)
(hours : minutes)
5.0
50*
1.70
5.0
45
0.85
5.0
55
0.55
2.5
50*
0.80
2.5
45
0.45
1.5
50
0.55
3.0
40
0.45
3.0
35
0.40
1.0
55
0.55
1.0
40
0.40
• Selectable for programmes Cotton 95°C and
Synthetics 60°C only.
"Prewash" button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time by
approximately 20 min.
"Intensive rinse" button
• The amount of water is increased to ensure a more
intensive rinse.
• This option is particularly suitable for areas with very
soft water, washing baby linen and people with skin
allergies.
"Rinse hold" button
• The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing
and prevent colours from changing.
• This option is particularly recommended for the
"Synthetics", "Daily load" and "Delicates"
programmes.
• It is useful if you want to postpone spinning to a later
time, or if you want to drain only.
• If you select "Rinse Hold", do not leave items to soak
for too long.
• As soon as the appliance stops in the rinse hold, the
"Anticrease" lamp of the sequence indicator lights up
and the lamp next to the "Start/Pause" button
flashes.
Terminate the "Rinse hold" option:
• Press the "Start/Pause" button; the programme
will terminate automatically with the final spin cycle
for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the "Drain"
programme and press the "Start/Pause" button.
"Variable spin" button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed "0" is selected, the final spinning is
cancelled but intermediate spin peaks remain during
2:05
the rinse. The water is drained out only.
2:30
START DELAY
2:00
1:30
The "Start delay" allows the user to run the machine at
1:15
his convenience, for example at night when electricity is
cheaper.
0:45
• Select programme, spin speed and options.
1:00
• Press the "Start Delay" button several times to
0:30
select a delay time by 1 to 23 hours.
0:45
• Start the programme (see "Progremme Start").
0:35
The indication lamp over the "Start delay" button
lights up and goes off when the programme starts.
• Once having pressed the "Start/Pause" button,
the countdown of the time delay begins. The time
delay indication on the display disappears when
the programme starts and is replaced by the
remaining programme time.
• After the "Start/Pause" button has been pressed,
the number of hours preselected can be reduced by
pressing again the "Start delay" button.
To cancel the "Start delay"
..before you press the "Start/Pause" button:
• Turn the programme selector to another position
or press the "Reset" button.
..after having pressed the "Start/Pause" button:
• Press the "Reset" button for at least 3 second. The
start delay indicator light goes off.
PROGRAMME START
Open the tap and press the "Start/Pause" button.
The indication lamp next to the "Start/Pause" button
lights up. The programme sequence indicator shows
the current programme phase, running from left to right
through Wash, Rinse, Spin/Drain. When the programme
phrase is finised, the corresponding indication goes out.
• Note: If there is a power interruption or if the
appliance is disconnected during the cycle, the
programme will run again from the point where it
was interrupted.
"DOOR OPEN" INDICATION
Before starting and after end of a programme, the lamp
lights to show the the lid can be opened. As long as a
wash programme is running, the lid remains locked and
must on no account be forced open. In case you have
an urgent need to open it during a running programme,
refer to "Cancel (Reset) a running programme before
the end".
RED INDICATIONS
"Service"
Lighting up of the "Service" indication can be caused
by a fault in an electrical component. Refer to the
"Troubleshooting Guide" in your "Instructions for Use";
if the fault persists, contact our After Sales Service.
"Water tap closed"
The appliance has no or insufficient water supply. Open
the water tap: if the indications still lights up, refer to the
"Troubleshooting Guide" in the Instructions for Use.
"Clean pump"
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned: in the
latter case refer to the Instructions for Use ("Removing
the Filter").
PROGRAMME END
• All the lights of the programme sequence indicator
are off, and the "Door open" indication lights up.
1. Turn the programme selector to the "Off/O"
position.
2. Close the water tap.
3. Open the lid and drum and unload the machine.
4. Leave the lid open for some time to allow the
interior of the machine to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the "Start/Pause" button to pause the
programme. The light flashes.
2. Select the new programme, any options and another
spin speed if you want.
3. Press the "Start/Pause" button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The "Reset" button cancels a programme before the
end. Press the "Reset" button for at least 3 seconds.
Any existing water is drained out before the door can be
opened.
Whirlpool is a registered trademark of Whirlpool USA.
5019 312 10546