Whirlpool CAM2752TQ - COMMCL WSHR 2SP 3CYC WH DIG D Manual de instrucciones de instalación - Página 5
Navegue en línea o descargue pdf Manual de instrucciones de instalación para Lavadora Whirlpool CAM2752TQ - COMMCL WSHR 2SP 3CYC WH DIG D. Whirlpool CAM2752TQ - COMMCL WSHR 2SP 3CYC WH DIG D 16 páginas. Commercial washer 120-volt, 60-hz models
Imprimir página
F
bose
112"
(1.3 cm)
L
nut
JB
1
U
• Use legs and nuts from parts
package,
Screw nut down
to within
1/2 inch (1,3 cm) of
base,
11.
Insert legs into correct
J
holes at each
front corner
of washer until nuts touch
washer,
Da Not tighten
nuts until Step 14,
2
mTilt washer backward
and
remove corner
posts, Gently
lower
washer to floor,
Move washer to its permanent
location. Remove cardboard
or
hardboard
from under washer.
1_
raising
back legs 1 inch (2,5 cm) off of floor,
To adjust rear self-leveling
legs, gently
lower washer to floor, Check
levelness
of the washer by placing
a
carpenter's
level on top of the
washer, first side to side; then front to
back,
4mlf
washer
is not level, adjust
the front legs up or down,
Make final
check
with level,
When washer is level, use wrench
to turn nuts on front legs up tightly
against washer base. If nuts are not
fight against washer base, the washer
may vibrate.
5
• Remove the service door of
the meter
case, Lift the service door
up at the back and remove,
Install
money accepting
device
(refer to
manufacturers
instructions
for proper
installation),
For machines
using coin
slides, use adapter
kit (provided
with
unit), Replace
meter case service
door,
l_)a
CHECK ELECTRICAL
REQUIREMENTS. BESURE YOU HAVE
CORRECTELECTRICAL S UPPLY AND
RECOMMENDEDGROUNDING
METHOD.
17.
Check that all parts are now installed,
See parts list, Page 3, If there is an
extra part, go back through
steps to
see which
step was skipped,
1
_% mTurn on water
faucets
and
check
for leaks, Tighten couplings
if
there is leaking,
Do Not overtighten;
this could cause
damage
to faucets,
tqk
m _j!
•Check
that you have all of
your tools, Check that the shipping
strap was removed
from the back of
the washer and used to secure the
drain hose,
If entire strop is not removed,
washer
may vibrate and be noisy.
0
• Plug power supply cord
into
grounded
outlet,
1 •
For electrolmechnical
models only. Check the wash cycle
time, The washer has a 9-minute
wash
in the Normal Cycle,
Remove the
timer from the meter case of the
washer to manually
start the timer,
Start the washer and allow it to
complete
the Normal cycle,
Rotate
counterclockwise
timer "off" position
Timer-frontview
Timers can be started
by turning
the
clutch
assembly
counterclockwise
until the washer starts to fill with water,
2
• If the washer fails to start or
does not give the proper
washer
cycle
time, the clutch
assembly of the
timer can be adjusted,
Remove the
timer from the meter case, Adjust the
clutch
assembly
screw clockwise
if
the washer does not start after the
coin slide mechanism
has been fully
actuated
in or out, Adjust the clutch
assembly
counterclockwise
if the
washer segment
of the Normal cycle
was less than 9 minutes,
timer clutch
adjuslment screw
PAGE 5