Whirlpool Cabrio,- WED7300X Manual de dimensiones - Página 2

Navegue en línea o descargue pdf Manual de dimensiones para Secadora Whirlpool Cabrio,- WED7300X. Whirlpool Cabrio,- WED7300X 2 páginas. Top-loading high efficiency low-water washer
También para Whirlpool Cabrio,- WED7300X: Manual de uso y mantenimiento (40 páginas), Manual de uso y mantenimiento (40 páginas), Manual de uso y mantenimiento (36 páginas), Manual de uso y mantenimiento (32 páginas), Manual de instalación (16 páginas), Manual de uso y mantenimiento (40 páginas), Manual de uso y mantenimiento (40 páginas), Dimensiones e información de instalación (1 páginas), Manual de uso y mantenimiento (40 páginas), Manual de uso y mantenimiento (48 páginas), Manual de uso y mantenimiento (40 páginas), Manual de uso y mantenimiento (40 páginas), Manual de uso y mantenimiento (40 páginas), Manual de uso y mantenimiento (44 páginas), Manual de uso y mantenimiento (19 páginas), Uso y cuidado Gude (44 páginas), Manual de uso y mantenimiento (44 páginas)

Imprimir página

Whirlpool Cabrio,- WED7300X Manual de dimensiones

ELECTRICAL REQUIREMENTS

To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical

supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit

breaker is recommended. Connect to an individual branch circuit.

VENTING REQUIREMENTS

xhaust venting: Exhaust your dryer to the outside. 4" (102 mm)

diameter vent is required. Rigid or flexible metal exhaust vent

must be used. Do not use plastic or metal foil vet. Exhaust hood

must be at least 12" (305 mm) from the ground or any object that

may be in the path of the exhaust.

Exhaust hoods:

Recommended Styles:

Louvered Hood

Acceptable Style:

Angled Hood

Determine vent path:

Select route that will provide straightest and most direct

■

path outdoors.

Plan installation to use fewest number of elbows and turns.

■

When using elbows or making turns, allow as much room

■

as possible.

Bend vent gradually to avoid kinking.

■

Use as few 90° turns as possible.

■

Determine vent length and elbows needed for best

drying performance:

Use following Vent System Chart to determine type of vent

■

material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified

in Vent System Chart. Exhaust systems longer than those

specified will:

Shorten life of dryer.

■

Reduce performance, resulting in longer drying times

■

and increased energy usage.

Because Whirlpool Corporation policy includes a continuous commitment to improve

our products, we reserve the right to change materials and specifications without notice.

Box Hood

The Vent System Chart provides venting requirements that will

help achieve best drying performance.

Whirlpool Vent System Chart

Type

Number of

of vent

90° elbows

Rigid metal

NOTE: Bottom exhaust installations have a 90º turn inside the

dryer. To determine maximum exhaust length, add one 90º turn

to the chart.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

Box/louvered

Angled

hoods

64 ft. (20 m)

58 ft. (17.7 m)

54 ft. (16.5 m)

48 ft. (14.6 m)

44 ft. (13.4 m)

38 ft. (11.6 m)

35 ft. (10.7 m)

29 ft. (8.8 m)

27 ft. (8.2 m)

21 ft. (6.4 m)