Whirlpool WGD8300SE Instrucciones de uso - Página 7
Navegue en línea o descargue pdf Instrucciones de uso para Secadora Whirlpool WGD8300SE. Whirlpool WGD8300SE 8 páginas. Dimensions
También para Whirlpool WGD8300SE: Manual de uso y mantenimiento (28 páginas), Dimensiones (1 páginas)
Imprimir página
Is it a gas dryer?
The gas valve clicking is a normal operating sound.
Are the four legs installed, and is the dryer level front to
back and side to side?
The dryer may vibrate if not properly installed. See the
Installation Instructions.
Is the clothing knotted or balled up?
When balled up, the load will bounce, causing the dryer to
vibrate. Separate the load items and restart the dryer.
Timer does not noticeably advance
Is the dryer set to Timed or Air Dry?
The timer moves slowly and continuously for the time setting.
Is the dryer set to Automatic Drying?
The timer moves only when the clothing is mostly dry. See
"How Automatic Drying Works" in "Dryer Use."
Dryer Results
Clothes are not drying satisfactorily, drying times are too long,
or load is too hot
Is the lint screen clogged with lint?
Lint screen should be cleaned before each load.
WARNING
Fire Hazard
Use a heavy metal vent.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in death
or fire.
Is the exhaust vent or outside exhaust hood clogged with
lint, restricting air movement?
Run the dryer for 5-10 minutes. Hold your hand under the
outside exhaust hood to check air movement. If you do not
feel air movement, clean exhaust system of lint or replace
exhaust vent with heavy metal or flexible metal vent. See the
Installation Instructions.
Are fabric softener sheets blocking the grille?
Use only one fabric softener sheet, and use it only once.
Is the exhaust vent the correct length?
Check that the exhaust vent is not too long or has too many
turns. Long venting will increase drying times. See the
Installation Instructions.
Is the exhaust vent diameter the correct size?
Use 4" (10.2 cm) diameter vent material.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Place dryer at least 18 inches (46 cm) above the floor
for a garage installation.
Failure to do so can result in death, explosion, or fire.
Is the dryer located in a room with temperature below
45ºF (7ºC)?
Proper operation of dryer cycles requires temperatures above
45ºF (7ºC).
Is the dryer located in a closet?
Closet doors must have ventilation openings at the top and
bottom of the door. Sides and front of dryer require a minimum
of 1" (2.5 cm) of airspace, and the rear of the dryer requires 5"
(12.7 cm). See the Installation Instructions.
Has an air dry cycle been selected?
Select the right cycle for the types of garments being dried.
Is the load too large and heavy to dry quickly?
Separate the load to tumble freely.
Cycle time too short
WARNING
Excessive Weight Hazard
Use two or more people to move and install dryer.
Failure to do so can result in back or other injury.
Is the automatic cycle ending early?
The load may not be contacting the sensor strips. Level the
dryer.
Change the dryness level setting on Automatic Cycles.
Increasing or decreasing the dryness level will change the
amount of drying time in a cycle.
Lint on load
Is the lint screen clogged?
Lint screen should be cleaned before each load.
Stains on load or drum
Was dryer fabric softener properly used?
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially dried load can stain
your garments.
Drum stains are caused by dyes in clothing (usually blue
jeans). This will not transfer to other clothing.
7