Whirlpool 36" (91.4 CM) GAS BUILT-IN COOKTOP Instrucciones de instalación y manual de uso y mantenimiento - Página 10

Navegue en línea o descargue pdf Instrucciones de instalación y manual de uso y mantenimiento para Campana de ventilación Whirlpool 36" (91.4 CM) GAS BUILT-IN COOKTOP. Whirlpool 36" (91.4 CM) GAS BUILT-IN COOKTOP 28 páginas. 36" (91.4 cm) island-mount canopy range hood
También para Whirlpool 36" (91.4 CM) GAS BUILT-IN COOKTOP: Manual de instrucciones de instalación (16 páginas), Manual de uso y mantenimiento (32 páginas)

Imprimir página

RANGE HOOD USE

Check Operation

The canopy hood is designed to remove smoke, cooking vapors

and odors from the cooktop area. For best results, start the hood

before cooking and allow it to operate several minutes after the

cooking is complete to clear all smoke and odors from the

kitchen.

Hood control panel

The hood controls are located on the underside of the canopy.

Operating the light

1. Press the "B" button. The light should turn on.

2. Press the "B" button again. The light should turn off.

Operating the blower and adjusting blower speed

1. Press the "C" button for low speed. "D" button for medium

speed. "E" button for high speed.

2. Press the "C" button again. The blower should turn off.

RANGE HOOD CARE

Be sure lights are cool before cleaning the hood.

Exterior surfaces

Clean the range hood with a mild detergent and soft cloth. Do not

use abrasive cleanser or steel wool pads.

Metal grease filters

The filters should be washed frequently. Place metal filters in

dishwasher or hot detergent solution to clean.

Drain water through edge holes and let each filter dry thoroughly

before replacing it.

To remove metal filters:

1. Turn blower and lights off.

2. Push handle toward the rear and pull downward.

3. Pull filter toward the front.

Cleaning

To replace the metal grease filters:

4. Insert back edge of filter into rear track of the filter opening.

5. Push handle toward the rear and push filter up.

6. Pull filter toward the front and insert into front track.

Charcoal Filters - For non-vented (recirculating) installations

The charcoal filters capture unpleasant cooking odors. They can

be cleaned and reactivated. With normal use the filter should be

cleaned every second month (when using the hood 2.5 hours per

day, on average).

Clean the filter in the dishwasher using normal detergent and

choosing the highest temperature setting. Wash the filter

separately. To reactivate the filter, the filter should be dried in an

oven for 10 minutes with a maximum temperature of 210°F

(100°C).

After approximately three years of use, the charcoal filter should

be replaced.

To install charcoal filters

1. Turn blower and lights off.

2. Remove the metal grease filters by pushing handle toward the

rear and pull downward.

3. Pull filter toward front.

4. Set the filter face down on a protective cover such as a towel.

5. Install charcoal filter on rear of metal filter with metal wires

provided in filter packaging.

A. Metal wires

B. Charcoal filter

C. Metal filter

To replace the metal grease filters:

6. Insert back edge of filter into rear track of the filter opening.

7. Push handle toward the rear and push filter up.

8. Pull filter toward the front and insert into front track.

To replace charcoal filter

1. Turn blower and lights off.

2. Remove the metal grease filters by pushing handle toward the

rear and pull downward.

3. Pull filter toward front.

4. Set the filter face down on a protective cover such as a towel.

5. Remove metal wires and clean or discard charcoal filter.

6. Install cleaned or replacement charcoal filter on rear of metal

filter with metal wires provided in filter packaging.

To replace the metal grease filters:

7. Insert back edge of filter into rear track of the filter opening.

8. Push handle toward the rear and push filter up.

9. Pull filter toward the front and insert into front track.