Ergo In Demand CrossRoads Instrucciones de montaje

Navegue en línea o descargue pdf Instrucciones de montaje para Mobiliario interior Ergo In Demand CrossRoads. Ergo In Demand CrossRoads 2 páginas. Newspaper display unit

Imprimir página
Figure 2
Base Assembly
Top Asm.eps
Top Assembly
Flat Washer
and Hex Nut
4
1
/
" Hex Head Bolts
2
with Lock Washers
and Flat Washers
Left End Panel
Figure 4
Ergo In Demand, Inc. • 4900 Industry Drive • Central Point, OR 97502 • Tel 1-800-888-6024 • www.ergoindemand.com
Figure 4
CrossRoads
Base Assembly
Figure 1
Left End Panel
Assembly
and Flat Washers
Top Assembly
Figure 1
Base Assembly.eps
Left End Panel
Figure 3
2" Hex Head Bolts
with Lock Washers
and Flat Washers
Right End Panel
Base Assembly
Shared End Panel
Glides
Assembly Instructions
Newspaper Display Unit
®
August 2008
Left End Panel
and Flat Washers
and Flat Washers
Right End Panel
Glides
Rt. End Pnl Install.eps
Figure 3
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must
be tightened securely and must be checked periodically
after assembly. Failure to assemble properly, or to secure
parts may result in assembly failure and injury.
Tools Required:
• #2 Phillips screwdriver
•
/
" socket
1
2
• Socket wrench
Hardware Included:
• #8 x
/
" screws
5
8
• #8 x 1
/
" screws
1
4
• #10 x 1
/
" pan head screws
1
2
•
/
" x 2" hex head bolt
5
16
•
/
" x 4
/
" hex head bolt
5
1
16
2
•
/
" lock washer
5
16
•
/
" at washer
5
16
•
/
" hex nut
5
16
• Metal pins
1. Set back edge of left end panel on at
surface (holes to inside – if it's a
curved end panel make sure the
curved edge is up).
2. Align the side holes in the base
assembly with the lower holes in the
left end panel. Insert 2" hex head bolts
with lock washers and at washers into
the base and end panel (Figure 1).
3. Align the side holes in the top
assembly with the upper holes in the
left end panel (Figure 2). Make sure
the faceplate on the top assembly is to
the front and that the back panel
groove is to the back. Insert 2" hex
head bolts with lock washers and at
washers into the top assembly and
end panel. Tighten.
4. For single starter unit (stand-alone)
and nal end panel for connecting
units: Take the right end panel (holes
to inside) and align the side with the
holes in both the base and the top
assembly (Figure 3). Insert 2" hex
head bolts with lock washers and at
washers into the base and top
Base Assembly
assembly. Tighten.
5. For adder units (connecting) – Align
the side holes in the shared panel
(holes both sides) with the holes in
both the base assembly and the top
assembly. Insert 4
with lock washers, at washers and
nut into the base assembly. Do not
tighten (Figure 4).
6. Align the side holes in both the base
and top assembly with the side holes
in the right end panel. Insert 2" hex
head bolts with lock washers and at
washers into base assembly and top
assembly (Figure 4).
7.Tighten all 2" and 4
Insert glides into all end panels.
/
" hex head bolts
1
2
/
" hex head bolts.
1
2