ergochair Ergo - Scoot Low-Profi le Creeper Manual de montaje y uso - Página 2

Navegue en línea o descargue pdf Manual de montaje y uso para Mobiliario interior ergochair Ergo - Scoot Low-Profi le Creeper. ergochair Ergo - Scoot Low-Profi le Creeper 2 páginas.

Imprimir página

Ergo - Scoot™ Low-Proﬁ le Creeper

Ergo-Scoot Assembly:

1. Open the box and remove the protec ve packing foam.

2. Carefully cut away the plas c holding the backrest to the seat. Do NOT damage the

foam seat or backrest with the knife.

3. Set the backrest aside where it will not be lost or damaged.

4. Carefully remove the protec ve plas c from both side tool trays and remove the

casters, fasteners, spring release and the gas spring. Place the components where

they will not be lost or damaged.

5. Leave the seat on the cardboard shipping box.

6. Verify all the components are present using the parts list.

7. Conﬁ gure the Scoot with or without spacers and op onal risers.

a. Without Risers

i. Turn over the seat and a ach the two locking casters and spacers (op onal) to

the front of the seat using four SHCS M8 x 20, ﬂ at washers, and lock washers

on each caster. (If using the op onal spacers use the M8 x 40 SHCS.)

ii. A ach the two swivel casters (without locks) and spacers (op onal) to the rear

of the seat using four SHCS M8 x 20 with ﬂ at washers, lock washers, and hex

nuts on each caster. (If using the op onal spacers use the M8 x 40 SHCS)

b. With Risers

i. A ach four risers to the seat using four SHCS M8 x 20 with ﬂ at washers, lock

washers, and hex nuts (verify the riser side with one hole is closest to the seat

as shown to the right).

ii. A ach the two locking casters to the front two risers using the SHCS M8 x 25

with ﬂ at washers, lock washers, and hex nuts.

iii. A ach the two swivel casters (without locks) to the rear two risers using the

SHCS M8 x 20 with ﬂ at washers, lock washers, and hex nuts.

8. Turn the seat onto its casters.

Install the backrest using two hex head bolts (HHB) M14 x 50 and two M14

nyloc nuts. Do not over ghten. The backrest must be able to move freely

about the pivot points created by the fasteners.

10. Insert the spring release assembly into the square channel under the seat

un l the threaded opening is visible in the middle slot. The backrest spring

release handle may be installed on either the right or le -hand side of the seat.

11. Thread the backrest gas spring all the way into the release mechanism.

12. Thread the lock nut and pad down the spring rod un l it contacts the

spring release mechanism. Make ﬁ nger ght.

13. Insert the top of the gas spring into the backrest moun ng ﬂ ange.

14. Secure the spring to the moun ng ﬂ ange with the HHB M8 x 25 and nyloc nut.

Step 14

Step 7a

Step 7b

Steps 9 - 13

15. The backrest should now recline. Sit on the Scoot and trigger the

spring release handle while pushing against the backrest. If the backrest does

not recline:

a. Remove the M8 HHB and nut securing the spring to the backrest.

b. Loosen the lock nut and then a empt to ghten the gas spring an addi onal

rota on.

c. Re ghten the lock nut onto the release mechanism.

d. Rea ach the gas spring to the backrest moun ng ﬂ ange and a empt to recline

the backrest.

e. If the backrest does not recline, contact Ergochair.

16. A ach one tool tray to each side of the Scoot using three HHB M6 x 12 and

M6 ﬂ anged lock nuts on each tool tray.

To clean the Ergo-Scoot:

1. While Marine Vinyl is water, stain and abrasion

resistant, it is s ll a porous material which can

become clogged with dirt. Wash the

Scoot vinyl frequently using soap and water.

2. Wipe the Vinyl and the Frame of the Scoot and dry

a er cleaning.

3. If a more powerful cleaner is required, use a gentle

cleaner, similar to Simple Green® or a small amount

of dish soap and a so bristle brush.

4. Rinse with water and wipe dry, then allow to air dry fully.

5. Do not use bleach, vinegar, alcohol or excessivly acidic or basic cleaners. These can dry out the vinyl and cause cracking.

6. Store the Scoot in a clean, well ven lated and dry area.

Parts List:

Assembly and User Guide

P/N 5900300 - Rev. A - May 2023

Steps 15 a-e

Step 16

Item

Descrip on

Qty.

No.

SCOOT SEAT

SCOOT BACKREST

SCOOT BACKREST GAS SPRING

SCOOT SPRING RELEASE

LOCKING CASTER

SWIVEL CASTER

TOOL TRAY

Spacer 20 mm (Op onal)

HHB M14 X 50 (Backrest Pivot Fasteners)

NUT, NYLOC M14 (Backrest Pivot Fasteners)

HHB M8 X 25 (Secures Backrest Gas Spring)

NUT, NYLOC M8 (Secures Backrest Gas Spring)

HHB M6 X 12 (Secures Tool Trays)

NUT, FLANGED LOCKING M6 (Secures Tool Trays)

SHCS M8 X 20 (Secures Casters)

WASHER, FLAT M8 (Secures Casters)

LOCK WASHER M8 (Secures Casters)

NUT, M8 (Secures Casters)

SHCS M8 x 40 (Spacer Kit)

1645 Lemonwood Drive

Santa Paula, CA 93060 USA

(800) 253-2363 bendpak.com