ERGODYNE 19770 Manual

Navegue en línea o descargue pdf Manual para Accesorios para herramientas eléctricas ERGODYNE 19770. ERGODYNE 19770 6 páginas. Tape measure trap

Imprimir página

SQUIDS

TOOL ATTACHMENTS

TAPE MEASURE TRAP

WWW.ERGODYNE.COM // 800 225 8238

Fig. 1

Fig. 3a

Fig. 3c

Fig. 2

Fig. 3b

The Squids® Tape Measure Trap is designed for ease-of-use, and to help reduce the risk

of dropped tools when used with an appropriate tethering system (refer to Using A

Tethering System instructions).

WARNINGS: All warnings and instructions must be read and understood before using this

product. Failure to do so may result in property damage, serious injury, or death.

• Never exceed the allowable weight capacity for any Tape Measure Trap. There are two

Tape Measure Trap sizes.

• Weigh the tool or tools to be tethered to ensure they do not exceed the maximum

safe working capacity of the tool lanyard or any part of your tethering system. Refer

to the label or product marking information for maximum capacity information.

• Always inspect Tool Attachments prior to, and after, each use (refer to INSPECTION

instructions).

• Do not wrap a Tool Attachment around sharp or rough edges.

• Never modify or alter your Tool Attachments.

• Never modify a tool that could result in manufacturer guideline deviation.

• Do not use this product if it interferes with the tool's safe working condition.

• Use extra precaution around moving machinery or parts, electrical hazards, chemical

hazards or other apparent hazards.

INSTRUCTIONS

1. Undo the hook and loop straps and open the Tape Measure Trap. [fig. 1]

2. Place the tape measure into the trap, with the back of the tape measure facing the

D-Ring on the back of the trap. [fig. 2]

3. Tightly fasten the hook and loop straps, securing the tape measure. [fig. 3a, 3b, 3c]

4. Attach a tool lanyard to the D-Ring to complete an appropriate tethering system

(refer to Using A Tethering System instructions).

*For an optimal fit, remove the belt clip from the tape measure before attaching the Tape

Measure Trap.

*For further instructions, watch the product video on www.ergodyne.com.

All tools and/or equipment used in conjunction with a Tape Measure Trap should be

regularly inspected by a competent person. Ensure any associated tethering system

is properly attached to the trap/tool and is not damaged. If any part of the tethering

system—including a Tape Measure Trap—has knowingly been involved in a drop, it must

immediately be taken out of service and replaced (refer to Using A Tethering System

instructions).

USING YOUR TETHERING SYSTEM

1. Always keep tools tethered while at heights. When exchanging tools, use one of the

following methods:

a. Use a 100% tie-off by ensuring the tool is tethered to a secondary anchor—or

secured in a rated container—before disconnecting from the initial anchor point.

b. Exchange tools over a secure area. (e.g. Inside a controlled container, over a

platform, etc.).

2. Required clearance:

a. When using Squids® Tool Attachments, determine the fully extended length of the

lanyard used, plus the length of the tool between where the lanyard is anchored

and the nearest person or sensitive object.

INSPECTION

Inspect your tethering system before and after each use. All equipment should be

regularly inspected by a competent person. Ensure the tethering system is properly

attached to the tool and is not damaged.

Before each use, check the following:

• Examine webbing, stitching and other soft materials for cuts, tears, heat trauma or

other damage.

• Examine all hardware for rust or corrosion, abnormal distortion (twists, bends), cracks

or breaks, or any other damage.

• Ensure carabiners and their gates function and lock properly. Examine swivels,

modular buckles, and any other components, to ensure proper function and that there

is no damage.

• Examine markings on the product and labels for legibility.

• If any part of the tethering system has knowingly been involved in a drop, it must

immediately be taken out of service and replaced. If any tethering system component

fails any part of an inspection, discard and replace the product immediately.

STORAGE AND CARE

• Store tool lanyards in a clean, dry location away from direct sunlight.

• To clean, use mild soap and water. Air dry.

DISCLAIMER

In no event shall Tenacious Holdings, Inc., be liable for any direct, indirect, punitive,

incidental, special, or consequential damages arising out of, or associated with, the misuse

of Squids® tethering system components (tool lanyards or attachments).

WARRANTY: We stand behind everything we make and guarantee our products to be

free of defects in materials and workmanship to the original purchaser for the product's

lifetime. Damage, abuse, and/or normal wear are not covered. Questions? Call Ergodyne

at +1-651-642-9889 (8 a.m. - 5 p.m. CST) or 800-225-8238.