Yamaha DTX520K Manual de montaje - Página 2

Navegue en línea o descargue pdf Manual de montaje para Instrumentos musicales Yamaha DTX520K. Yamaha DTX520K 2 páginas. Dtx drums
También para Yamaha DTX520K: Manual de montaje (2 páginas), Manual del usuario (48 páginas)

Imprimir página

Mounting snare and tom pads

Mount the snare pad on the rack's clamp rod. As

DTX540K: XP70

shown below, ensure that the rod section is fully in-

DTX520K: TP65

serted into the pad's mounting hole, and then fully

tighten the clamp bolt.

Clamp rod

XP80

If necessary, use clamp bolts A to E to adjust the

 Mounting the snare pad

height and angle of the snare pad. When doing so,

be sure to adjust one bolt at a time (i.e., loosen a

Attach the clamp bolt to the snare pad and provi-

bolt, adjust the pad, and then retighten before loos-

sionally tighten (by 5 or 6 turns).

ening another).

Clamp bolt (to be tightened

Clamp bolt B

in the direction shown)

Snare pad (rear side)

Clamp bolt D

Clamp bolt E

Clamp bolt C

Mounting the drum trigger module, cymbal pads, and hi-hat pad

 Mounting the cymbal and hi-hat pads

Cymbal pad:

PCY100

PCY135

Using a tuning key, loosen the stopper's key bolt.

Hi-hat pad:

PCY100

Drum trigger

module

Remove the wing nut, the two felt pads, and the bolt

cover from the cymbal holder.

 Mounting the drum trigger module

Attach the module stand (provided) to the underside

of the drum trigger module using the module stand

fastening screws.

Module stand

fastening screws

Module stand

Drum trigger module

(back side)

Place the stopper on the cymbal holder.

* If the key bolt was not sufficiently loosened in

Step 1 above, it may not be possible to pass the

stopper over the cymbal holder's shaft. In such a

Front of

case, loosen the key bolt as much as possible

module

without removing it.

Replace the bolt cover.

Place the module stand inside the holder clamp and

tighten the clamp bolt to secure in position.

Drum trigger

module

module stand

Insert

Clamp bolt

Holder clamp

* When assembling the bolt cover, turn until it no

longer rotates.

 Mounting the tom pad

As with the snare pad, attach the clamp bolt to each

of the three tom pads and provisionally tighten (by 5

or 6 turns).

Snare pad

Mount the three tom pads on the rack's clamp rods.

As shown below, ensure that the rod section is fully

Rod

section

inserted into each pad's mounting hole, and then

fully tighten the clamp bolt.

Tom pad

Insert

Clamp bolt

If necessary, use clamp bolts A to D to adjust the

height and angle of any of the pads. When doing so,

be sure to adjust one bolt at a time (i.e., loosen a

bolt, adjust the pad, and then retighten before loos-

ening another).

Clamp bolt A

Clamp bolt C

Clamp bolt D

Secure the stopper in place. With the stopper mak-

ing full contact with the bottom surface of the bolt

cover, tighten the stopper's key bolt using a tuning

key.

Stopper

[Cymbal pad]

Key bolt

Bolt cover

Tuning key

Full contact

Cymbal holder

Wing nut

Place one of the felt pads removed in Step 2 on the

cymbal holder.

Felt pads

Mount the pad unit on the cymbal stand. Lower the

Bolt cover

pad unit into place with the cymbal holder's shaft

passing through the central hole of the cup section.

When mounted, the stopper's pin should rest inside

the pad unit's smaller hole.

Cymbal holder

* If you were to play a cymbal pad without the stop-

per's pin positioned inside the smaller hole, the

pad could rotate, causing the cable to be pulled

out. It is very important, therefore, to ensure that

the stopper is secured as described in Step 5

above.

Assemble the felt pad that came with your pad unit.

* The second felt pad removed from the cymbal

holder in Step 2 above is not required for assem-

bly of your pad unit.

Tighten the wing nut to secure the pad unit to the

cymbal holder.

Bolt cover

Wing nut

Felt pad that came

with pad unit

Stopper

Pad unit

Cymbal holder

Felt pad

Bolt cover

Assembling the kick pad

If a drum mat (sold separately) is not available, lay a sheet of cardboard on the

floor to protect it from scratching.

Remove the wing bolts, spring washers, and washers from the kick pad body, and

line up each set nearby in the order in which it was removed.

Join the base section to the body as shown right, and then secure it in place by

assembling the wing bolts, spring washers, and washers removed in the previous

step from the base side.

Rod section

Clamp rod

Support plate

Insert

Position the hi-hat controller and kick pad as desired, referring to the standard assembly example on the other side.

Before starting assembly, lay a drum mat (sold separately) on the floor. Alternatively, you can place the packages' cardboard

NOTICE

boxes on the floor under the hi-hat controller and kick pad to protect it from damage.

Connect the pads to the drum trigger module.

As described below, connect the output of each pad to the corresponding trigger input jack on the drum trigger module.

Clamp bolt B

Insert the 9-channel snake cable's straight plugs into the drum trigger module's

trigger input jacks ([q SNARE] to [i KICK/o] and [HI-HAT CONTROL]).

• If you are using the standard setup, the stickers on each of the snake cable's

plugs will indicate the name of the corresponding pad.

[Drum trigger module's rear panel]

[Hi-hat pad]

[9-channel

Stopper

Bolt cover

snake cable]

Straight

Full contact

plugs

L-shaped

plugs

HH CON HI HAT CRASH

Connect the drum trigger module to a power supply.

Ensure that the (Standby/On) button is set to the Standby position, and then con-

nect the AC power adaptor to the DC IN jack

Hook the power adaptor's cord around the cord clip to secure it in place.

[Drum trigger module's rear panel]

DC IN jack

Stopper's pin

Smaller

Pad unit

hole

Use the cable bands to bind the cables to the rack as shown on the right. (

Plug the AC power adaptor into an AC wall socket.

This completes the assembly procedure.

Stopper

Cymbal holder

Body

Plug the 9-channel snake cable's L-shaped plugs into the correct pads.

[Locations of pad jacks]

Straight plug names

DTX500 jack names

(as shown on stickers)

1: qSNARE

SNARE

2: wTOM1/!0

TOM1

3: eTOM2/!1

TOM2

4: rTOM3/!2

TOM3

5: tRIDE

RIDE

6: yCRASH

CRASH

7: uHI-HAT

HI HAT

8: iKICK/o

KICK

HH CON

9: HI-HAT CONTROL

In the case of snare and tom pads, wrap the cables around the cable clips to pre-

vent them from being pulled out.

NOTICE

KICK

SNARE TOM1 TOM2 TOM3 RIDE

on the rear panel.

Cord clip

)

* For information about tuning the power on/off, checking the actual sound, and other subsequent steps,

refer to the Setting Up section of the owner's manual that came with your drum trigger module.

Spring washer

Washer

Wing bolt

Body

Base

Excessive bending can damage the pad cables. Ensure, there-

fore, that these cables are not bent at an extreme angle when

wrapped around the clips.