CALI neonLEDs NLED Manual de instrucciones de instalación - Página 7

Navegue en línea o descargue pdf Manual de instrucciones de instalación para Equipos de iluminación CALI neonLEDs NLED. CALI neonLEDs NLED 12 páginas. Neonleds series

Imprimir página
neonLEDs
Installation Instructions
1.
Measure area where neonLEDs will be installed.
U-channel
RECOMMENDATION: Use chalk line to ensure a straight installation.
0.5" gap
Apply silicone
2.
Cut U-Channel as necessary and secure with screws (by others), then
mount NLED to U-Channel.
3"
.5"
8'
U-channel
Power cord
0.5" gap
NOTE:
- Do not install power lead or end cap into U-Channel.
- Do not interfere with silicone or shrink tube while installing NLED into U-Channel.
- Cut U-Channel if it interferes with sealed shrink tube.
Apply silicone
Apply silicone
- When installing, do not pull on power leads or end caps. Pulling on NLED and extending
U-channel
.95"
flexible lights will cause the lights to expand during installation, then contract,
Line A
compromising the seal.
2b.
0.5" gap
Screw head must be flush to Line A.
19'6"
8'
8'
RECOMMENDATION: Use pan head screws with
Top of
extrusion
Apply silicone
Check the U-Channel opening.
LLED
Cutting line
9/16"
or
3"
smaller
.5"
8'
.95"
2c.
Apply double stick tape to hold NLED securely in U-Channel for
applications facing outward or downward.
9/16"
Bottom of
or
RECOMMENDATION:
extrusion
smaller
- 3M 4008 double stick tape 3/8" width (not included).
.95"
Lateral bend
- Leave open spaces where screws are present.
4" minimum radius
Cutting line
3.
Install NLED into channel. Use a wire puller stand to ensure secure
and correct installation.
0.64"
Bottom of
extrusion
Cutting line
0.84"
0.84"
0.64"
0.84"
™
20'
0.5" gap
Chalk line
Apply silicone
19'6"
8'
3'6"
0.5" gap
9/16"
Friction keeps
or
NLED from falling
smaller
Power cord
0.5" gap
3"
3'6"
.5"
U-Channel
Bottom of
head thickness less than .1".
extrusion
End cap
Apply silicone
Line A
Lateral bend
4" minimum radius
Convex bend 4"
Friction keeps
Double stick tape
Top of
minimum radius
NLED from falling
19'6"
3"
extrusion
8'
3'6"
.5"
LLED
Bottom of
extrusion
Double stick tape
Friction keeps
NLED from falling
Convex bend 4"
minimum radius
0.64"
0.64"
Concave bend 6"
minimum radius
Bottom of
extrusion
0.84"
0.84"
0.84"
0.84"
Lateral bend
4" minimum radius
Convex bend 4"
minimum radius
1.92"
Concave bend 6"
minimum radius
Bottom of
Wire puller stand
extrusion
(Refer to page 4 for additional details)
CALIFORNIA ACCENT LIGHTING, INC.
2034 E. Lincoln Ave. #431, Anaheim, CA 92806
ph. 800.921.CALI (2254) or 714.535-7900 \ fx. 714.535.7902
[email protected] \ calilighting.com
© CALI. All rights reserved. CALI reserves the right to make changes or withdraw specifications without prior notice.
0.84"
1.92"
4.
Mount NLED into channel, leaving a one half inch gap between
the channel and sealed power cord and sealed end cap.
U-channel
4b.
After installing, apply silicone on both ends for a complete seal.
0.5" gap
3"
.5"
Apply silicone
5.
Conduct continuity test.
U-Channel
End cap
Power cord
Power cord
3"
If a conductive
.5"
8'
path is formed
Double stick tape
between positive
and negative wire,
the multimeter will
beep. You need to
trouble shoot to
find the short.
Apply silicone
9/16"
(not included)
Line A
Line A
or
OFF
Ω
smaller
VDC
VAC
.95"
A
COM
VΩ
6.
U-channel
Set voltmeter to DC voltage, then test power source before connecting.
Top of
Top of
extrusion
extrusion
0.5" gap
Male pin
connector
OFF
LLED
LLED
Ω
DCV
DCA
Concave bend 6"
minimum radius
Apply silicone
U-Channel
A
COM
VΩ
End cap
Cutting line
Male pin
3"
7.
connector
Connect power source to power connector.
.5"
8'
6"
+ -
Power cord
End cap
4"
.95"
Line A
1.92"
1.92"
8.
Shrink tube
Minimum bend radius.
Top of
extrusion
LLED
Cutting line
2"
2"
U-channel
U-channel
0.5" gap
0.5" gap
0.5" gap
Apply silicone
Apply silicone
Apply silicone
(not included)
Apply silicone
3"
19'6"
3"
19'6"
.5"
8'
.5"
8'
Troubleshoot
19'6"
3"
Male pin
8'
3'6"
.5"
connector
9/16"
9/16"
OFF
OFF
Ω
VDC
Ω
VDC
or
or
VAC
VAC
smaller
smaller
A
COM
VΩ
A
COM
VΩ
.95"
.95"
Double stick tape
Friction keeps
NLED from falling
(Refer to page 6 for additional details)
OFF
Ω
VDC
VAC
A
COM
VΩ
OFF
OFF
Ω
DCV
Ω
DCV
DCA
DCA
180° 120V connector
DCV
power cord
A
COM
VΩ
A
COM
VΩ
0.5" gap
Apply silicone
Lateral bend
End cap
Lateral bend
(not included)
TRA power
Bottom of
4" minimum radius
Cutting line
4" minimum radius
Cutting line
Ω
source
extrusion
Apply silicone
A
Lateral bend
4" minimum radius
+ -
+ -
Convex bend 4"
180° 120V connector
minimum radius
power cord
19'6"
Concave bend 6"
Shrink tube
minimum radius
8'
3'6"
Apply silicone
Brown
(not included)
Blue
(Hot)
(Neutral)
NLED
Bottom of
extrusion
Green
9/16"
(Ground)
Friction keeps
or
NLED from falling
smaller
Apply silicone
(not included)
TRAXXX-E/UNV/24VDC/-10V
End cap
Bottom of
extrusion
Lateral bend
4" minimum radius
Convex bend 4"
minimum radius
Shrink tube
Bottom of
extrusion
NLED-24V
Step by Step (24V)
0.5" gap
0.5" gap
Apply silicone
Apply silicone
3"
3"
TRA
8'
3'6"
.5"
8'
3'6"
.5"
Good
U-Channel
U-Channel
180° 120V connector
End cap
power cord
End cap
If there is no
U-Channel
<1.5"
conductive path, the
End cap
multimeter will not
OFF
OFF
Double stick tape
Friction keeps
Double stick tape
Friction keeps
Ω
VDC
Ω
VDC
VAC
VAC
beep.
NLED from falling
NLED from falling
A
COM
VΩ
A
COM
VΩ
Male pin
connector
<1.5"
Apply silicone
(<38.1mm)
OFF
OFF
(not included)
Ω
DCV
Ω
DCV
DCA
DCA
Bottom of
Bottom of
extrusion
extrusion
NLED
A
COM
VΩ
A
COM
VΩ
Confirm the correct
voltage, depending on
OFF
DCV
the light strip.
DCA
Convex bend 4"
Convex bend 4"
minimum radius
minimum radius
COM
VΩ
Concave bend 6"
Concave bend 6"
minimum radius
minimum radius
3"
.5"
Bottom of
Bottom of
extrusion
extrusion
U-Channel
Black (-)
24VDC
Red (+)
End cap
White (-)
Optional Dimmer
Blue (+)
(not included)
Double stick tape
Line
NLED
Concave bend 6"
minimum radius
Brown
Blue
(Hot)
(Neutral)
Green
(Ground)
7 of 10
Apply silicone
(not included)
<1.
<1.
(<38.1
End cap
App
(no
Male pin
Shrink tube
connecto
End
Shrin