aerauliqa QS100 Manual de instalación - Página 3

Navegue en línea o descargue pdf Manual de instalación para Ventilador aerauliqa QS100. aerauliqa QS100 18 páginas.

Imprimir página

Installation manual

QS - Axial fan

Read this manual carefully before using the product and keep it

in a safe place for reference.

This product was constructed up to standard and in compliance

with regulations relating to electrical equipment and must be

installed by technically qualified personnel.

The manufacturer assumes no responsibility for damage to

persons or property resulting from failure to observe the

regulations contained in this booklet.

PRECAUTIONS FOR INSTALLATION, USE ANd MAINTENANC

• T he device should not be used for applications other than those speciﬁed in this manual.

• A fter removing the product from its packaging, verify its condition. In case of doubt,

contact a qualiﬁed technician. Do not leave packaging within the reach of small children

or people with disabilities.

• D o not touch the appliance with wet or damp hands/feet.

•This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge

if they have been given supervision or instruction concerning use of the appliance

in a safe way and understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by children without

supervision.

• D o not use the product in the presence of flammable vapours, such as alcohol, insecticides,

gasoline, etc.

• I f any abnormalities in operation are detected, disconnect the device from the mains

supply and contact a qualiﬁed technician immediately. Use original spare parts only for

repairs.

• T he electrical system to which the device is connected must comply with regulations.

• B efore connecting the product to the power supply or the power outlet, ensure that:

- the data plate (voltage and frequency) correspond to those of the electrical mains

- the electrical power supply/socket is adequate for maximum device power. If not,

contact a qualiﬁed technician.

• T he device should not be used as an activator for water heaters, stoves, etc., nor

should it discharge into hot air/fume vent ducts deriving from any type of combustion

unit. It must expel air outside via its own special duct.

• O perating temperature: 0°C up to +50°C.

• T he device is designed to extract clean air only, i.e. without grease, soot, chemical or

corrosive agents, or flammable or explosive mixtures.

• D o not leave the device exposed to atmospheric agents (rain, sun, snow, etc.).

• D o not immerse the device or its parts in water or other liquids.

• T urn off the main switch whenever a malfunction is detected or when cleaning.

• F or installation an omnipolar switch should be incorporated in the ﬁxed wiring, in

accordance with the wiring regulations, to provide a full disconnection under overvoltage

category III conditions (contact opening distance equal to or greater than 3mm).

• I f the supply cord is damaged, it must be replaced by the manufacturer, its service

agent or similarly qualiﬁed persons in order to avoid a hazard.

• D o not obstruct the fan or exhaust grille to ensure optimum air passage.

• E nsure adequate air return into the room in compliance with existing regulations in

order to ensure proper device operation.

• I f the environment in which the product is installed also houses a fuel-operating device

(water heater, methane stove etc., that is not a "sealed chamber" type), it is essential

to ensure adequate air intake, to ensure good combustion and proper equipment

operation.

• I nstall the product so that the impeller is not accessible from the air outlet side as

veriﬁed by contact with the Test Finger (test probe "B" of the norm EN61032) in

compliance with the current safety regulations.

• C eiling installation

In order to guarantee the IPX4 degree of protection against moisture in case of ceiling

Fig. 1

installation, use the appropriate ceiling mount kit, which is not included. Use only the

rear entry hole for supply cables. If there is a possibility of condensation along the air

discharge duct, provide a drainage system to prevent condensation from discharging

into the environment through the fan.

Attention: do not mount the product on the ceiling without this kit.

• W indow installation

In case of window installation it is necessary to use the appropriate window kit, which

is not included.

Attention: do not mount the product on the window without this kit.

INTROdUCTION

QS (fig. 1) is an axial fan designed to ensure air extraction in small/medium-sized rooms

such as bathrooms, toilets and kitchens.

Suitable for air discharge directly to the outside or in the presence of short linear duct

(less than 1.5m). Wall, ceiling or window installation (fig. 2).

TECHNICAL SPECIFICATIONS

• M aterial: High quality, impact and UV-resistant ABS colour RAL 9010.

• R ear reinforcement ring to prevent spigot deformation during installation.

• H igh efficiency aerodynamic fan with "winglet" blades to optimise quietness and

efficiency.

• S ingle phase induction motor with integral thermal protection.

• M otor mounted on high quality sleeve bearings.

• B B version (on request): motor mounted on ball bearings that guarantee a longer product

life cycle (30,000h) and suitable for cold climates.

• T he fan is double insulated: no earth connection is required.

• S uitable for continuous or intermittent operation.

• I PX4 degree of protection.

• P ower supply 220V to 240V~ 50/60Hz.

Code

QS90

QS100

QS120

QS150

VERSIONS

STANDARD

The fan is operated using a separate ON/OFF switch or via a light switch (ﬁg. 13A).

Airflow

Static pressure

Power

Sound pressure

dB(A) @3m

/h max

Pa max

W max

175

330