Yamaha AX-592 Manual del usuario - Página 20
Navegue en línea o descargue pdf Manual del usuario para Amplificador Yamaha AX-592. Yamaha AX-592 24 páginas. Natural sound stereo amplifier
TROUBLESHOOTING
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the AC power plug
and contact your authorized YAMAHA dealer or service center for help.
SYMPTOM
The unit fails to turn on when the POWER
switch is pressed, or turns off suddenly
soon after the power is turned on.
No sound.
Sound level is too low.
The sound suddenly goes off.
Only one speaker outputs sound.
There is a lack of bass and no ambience.
The sound "hums".
Sound level is low or sound is distorted
while playing a record on the turntable.
The volume level cannot be increased, or
sound is distorted.
Using the BASS, TREBLE, BALANCE, and
LOUDNESS controls and SUBSONIC
FILTER switch ( AX-592 and AX-892 only )
does not affect the tone.
The input source can not be changed,
though the INPUT selector is turned.
The remote control does not work.
The distance or range within which the
remote control can be used decreases.
The sound is degraded when listening with
the headphones connected to the compact
disc player or cassette deck that are
connected with this unit.
20
CAUSE
The AC power plug is not plugged in or is not
completely inserted.
The IMPEDANCE SELECTOR switch on the
rear panel is not set to the upper or the lower
end exactly.
Incorrect output cable connections.
The appropriate input source is not selected.
The SPEAKERS switches are not set
properly.
Speaker connections are not secure.
The jumpor pins (PRE OUT/MAIN IN) are not
connected properly. (AX-592 and AX-892 only)
The MUTING switch is pushed in. (Muting is
on) (AX-892 only)
The protection circuit has been activated
because of a short circuit, etc.
Incorrect setting of the BALANCE control.
Incorrect cable connections.
The cable polarity is reversed at the amplifier
or speakers.
Incorrect cable connections.
No connection from the turntable to the GND
terminal.
The LOUDNESS control is functioning.
The PHONO (MM/MC) switch is set to the
improper position ( AX-592 and AX-892 only ).
The power to the component connected to the
REC OUT terminals of this unit is off.
The CD DIRECT AMP or PURE DIRECT
switch is on.
The CD DIRECT AMP switch is on.
Direct sunlight or lighting (of an inverter type of
fluorescent lamp etc.) is striking the remote
control sensor of the unit.
The batteries of the remote control are too
weak.
The power to this unit is off.
REMEDY
Firmly plug in the AC power plug.
Set the switch to the upper or the lower end
exactly.
Connect the cables properly. If the problem
persists, the cables may be defective.
Select an appropriate input source with the
INPUT selector.
Set the SPEAKERS switch, which corresponds
to the speakers to be used, to ON.
Secure the connections.
Connect the jumper pins properly.
(AX-592 and AX-892 only)
Push the MUTING switch again. (Muting is off)
(AX-892 only)
Turning the unit off and then on will reset the
protection circuit.
Adjust it to the appropriate position.
Connect the cables properly. If the problem
persists, the cables may be defective.
Connect the speaker cables correctly.
Firmly connect the cables. If the problem
persists, the cables may be defective.
Make the GND connection between the
turntable and this unit.
Set the LOUDNESS control to the FLAT
position.
Set the PHONO (MM/MC) switch to the proper
position ( AX-592 and AX-892 only ).
Turn the power to the component on.
The CD DIRECT AMP and PURE DIRECT
switches must be switched off to use those
controls.
Switch off the CD DIRECT AMP switch.
Change the position of the unit.
Replace the batteries with new ones.
Turn the power to this unit on.