Yamaha CX-2 Manual del usuario - Página 3

Navegue en línea o descargue pdf Manual del usuario para Amplificador Yamaha CX-2. Yamaha CX-2 19 páginas. Natural sound stereo pre-amplifier

Imprimir página

Caution: Read this before operating your unit

To ensure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

Install your unit in a cool, dry, clean place – away from

windows, heat sources, and too much vibration, dust,

moisture or cold. Avoid sources of hum (transformers,

motors). To prevent fire or electrical shock, do not

expose to rain and water.

Do not operate the unit upside-down. It may overheat,

possibly causing damage.

Never open the cabinet. If a foreign object drops into

the set, contact your dealer.

Always set the volume control to "–

the audio source play: increase the volume gradually to

an appropriate level after the play is started.

1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC, to

use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high quality

shielded cables. Cable/s supplied with this product

MUST be used. Follow all installation instructions.

Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC Regulations,

Part 15 for Class "B" digital devices. Compliance with

these requirements provides a reasonable level of

assurance that your use of this product in a residential

environment will not result in harmful interference with

other electronic devices.

This equipment generates/uses radio frequencies and, if

not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

FEATURES

Continuously Variable Loudness Control

only

PURE DIRECT Switch to Reproduce the Purest Source

Sound

SUBSONIC FILTER Switch to Cut Out Undesirable Ultra-

Low-Frequency Signals

SUPPLIED ACCESSORIES

After unpacking, check that the following parts are contained.

Remote Control Transmitter.

CX-1

CX-2

PHONO

POWER

—

PRESET

A/B/C/D/E

TUNER

SKIP

PLAY

PAUSE/STOP

DISC SKIP

DIR A

DECK A/B

DIR B

AUX

PLAY

TAPE 1

C H A P T E R

REC/PAUSE

STOP

REC MUTE

TAPE 2

TAPE 3

REC/PAUSE

REC

PAUSE

DIR A

DIR B

TAPE 1

REC MUTE

TAPE 2

MUTING

—

MUTE

VOLUME

∞

" before starting

FCC INFORMATION

For CX-2

Batteries

Audio Connection Cord

Do not use force on switches, knobs or cords. When

moving the set, first turn the unit off. Then gently

disconnect the power plug and the cords connecting to

other equipment. Never pull the cord itself.

Do not attempt to clean the unit with chemical solvents;

this might damage the finish. Use a clean, dry cloth.

When not planning to use this unit for long periods of

time (ie., vacation, etc.), disconnect the AC power plug

from the wall outlet.

Be sure to read the "Troubleshooting" section on

common operating errors before concluding that your

unit is faulty.

Do not connect audio equipment to the AC outlets on

the rear panel if that equipment requires more power

than the outlets are rated to provide.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product

is found to be the source of interference, which can be

determined by turning the unit "OFF" and "ON", please try

to eliminate the problem by using one of the following

measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

PHONO (MM/MC) Selector Switch

Video Signal Input/Output Capability (Including S Video

Connections)

For CX-2 only

Remote Control Capability

REMOTE CONTROL Connector to Make the Power of

the Power Amplifier MX-1 or MX-2 Controlled by This

Unit

Remote Control Cable