Zanussi ZD 19/6 DAC Manual de instrucciones - Página 3

Navegue en línea o descargue pdf Manual de instrucciones para Frigorífico Zanussi ZD 19/6 DAC. Zanussi ZD 19/6 DAC 6 páginas. Fridge-freezer zd 19/6 dac

Imprimir página

Door reversal

Unplug the refrigerator from the wall socket before
performing the following operations:
1. Remove the lower hinge (1), and the support foot
(2).
2. Unscrew the front left support foot and screw it
into the corresponding position on the opposite
side.
3. Unscrew the two screws which hide the fixing
holes of the hinge on the left-hand side.
4. Detach the lower door from the central hinge (H).
5. Remove the centrai hinge and detach the upper
door from the pin (G). Unscrew the pin (G) and
screw it into the corresponding position on the
opposite side, after having removed the plugs
which must be refitted on the other side.
6. Remove the two plugs, and remount them on the
other side.
7. Re-assemble the upper door, the centrai hinge
and the lower door.
8. Re-assemble the lower hinge (1) and the support
foot (2) on the opposite side.
Attention
After completion of the door reversibility operation,
verify that the door gasket is adherent to the cabinet.
If the ambient temperature is cold (i.e. in Winter), the
gasket may not fit perfectly to the cabinet. In that
case, wait for the natural fitting of the gasket or
accelerate this process by heating up the part
involved with a normal hairdrier.
10
G
3
1
2
D715 PIED/M
D419
H
Environment Protection
This appliance does not contain gasses which
could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The
appliance shall not be discarded together with
the urban refuse and rubbish. Avoid damaging
the cooling unit, especially at the rear near the
heat exchanger. Information on your local
disposal sites may be obtained from municipal
authorities. The materials used on this appliance
marked by the symbol
are recyclable.
CONTENTS
Temperature regulation

USE

Cleaning the interior

Before using the appliance for the first time, wash
the interior and all internal accessories with luke-
warm water and some neutral soap so as to remove
the typical smell of a brand-new product, then dry
thoroughly.
Do not use detergents or abrasive
powders, as these will damage the finish.
Operation
Insert the plug into the wall socket.
Open the refrigerator door and turn the thermostat
knob, clockwise, beyond the «O» (STOP) position.
The appliance will start to operate.
To stop operation, simply turn the thermostat knob to
position «O».
Temperature regulation
The temperature is automatically regulated and can
be increased to achieve a higher temperature
(warmer) by rotating the thermostat knob toward
2
3
Maintenance
3
3
Periodic cleaning
3
Periods of no operation
4
Interior light
4
Defrosting
4
Customer service and spare parts
4
Installation
4
5
Location
5
Rear spacers
5
Electrical connection
5
Door reversal
6
lower settings or reduced (colder) rotating the knob
towards higher settings.
However, the exact setting should be chosen
keeping in mind that the temperature inside the
refrigerator depends on:
•
room temperature;
•
how often the door is opened;
•
the quantity of food stored;
•
location of appliance.
A medium setting is generally the most suitable.
Important
If the ambient temperature is high or the
appliance is fully loaded, and the appliance is set
to the lowest temperatures, it may run
continuously causing frost to form on the rear
wall. In this case the dial must be set to a higher
temperature to allow automatic defrosting and
therefore reduced energy consumption.
2222 181-73
6
6
6
7
7
7
7
7
8
9
9
9
9
10
3