Zanussi ZWS 588 Manual del usuario - Página 7

Navegue en línea o descargue pdf Manual del usuario para Lavadora Zanussi ZWS 588. Zanussi ZWS 588 24 páginas. Front-loading washing machine

Imprimir página

Select the required programme by turning the

programme selector dial (1)

Turn the programme selector dial to the required pro-

gramme. The washing machine will automatically select

the maximum spin value provided for the programme you

have chosen. You can change this value by pressing the

corresponding button. The green pilot light of the button

6 starts to flash.

The selector dial can be turned either clockwise or coun-

terclockwise. Turn to position « O » to reset programme/

Switching the machine off.

At the end of the programme the selector dial must be

turned to position O, to switch the machine off.

Caution! If you turn the programme selector dial to

another programme when the machine is working,

the red pilot light of button 6 will blink 3 times to indicate

a wrong selection. The machine will not perform the new

selected programme.

Select the required temperature by turning the

temperature selector dial (2)

Turn clockwise this dial to select the more convenient to

your laundry washing temperature.

Select the available options by pressing buttons 3,

4 and 5

Depending on the programme, different functions can be

combined. These must be selected after choosing the de-

sired programme and before starting the programme.

When these buttons are pressed, the corresponding pilot

lights illuminate. When they are pressed again, the pilot

lights go out. If an incorrect option is selected, the inte-

grated red pilot light of the button 6 flashes for 3 times.

For the compatibility among the washing pro-

grammes and the options see chapter «Washing

Programmes».

Start the programme by pressing button 6

To start the selected programme, press the button 6 , the

corresponding green pilot light stops blinking. The ap-

pliance starts operating and the only pilot light corre-

sponding to the running phase stays on.

To interrupt a programme which is running, press the

button 6 : the corresponding green pilot light starts blink-

ing.

To restart the programme from the point at which it was

interrupted, press the button 6 again .

If an incorrect option is selected, the red pilot light of the

button 6 blinks 3 times.

Altering an option or a running programme

It is possible to change some options before the pro-

gramme carries them out.

Before you make any change, you must PAUSE the ap-

pliance by pressing the button 6 .

Changing a running programme is possible only by re-

setting it. Turn the programme selector dial to O and then

to the new programme position. Start the new programme

by pressing the button 6 again. The washing water in the

tub will be not emptied out.

Interrupting a programme

Press the button 6 to interrupt a programme which is

running, the corresponding green pilot light starts blink-

ing.

Press the button again to restart the programme.

Cancelling a programme

Turn the selector dial to

is running. Now you can select a new programme.

Opening the door

After the programme has started the door is locked. If, for

any reason, you need to open it, set firstly the machine to

PAUSE by pressing the button 6 . After a few minutes it

will be possible to open the door.

If the door remains locked, this means that the machine

is already heating or that the water level is too high. In

any case, do not try to force the door!

If you cannot open the door but you need to open it you

have to switch the machine off by turning the selector dial

to O . After a few minutes the door can be opened (pay

attention to the water level and temperature!) .

After closing the door, it is necessary to select the pro-

gramme and options again and to press button 6 .

At the end of the programme

The machine stops automatically. The pilot light of button

6 and the pilot light corresponding to the just finished

washing phase go off. The light 7.3 illuminates.

If a programme or an option that ends with water left in

the tub has been selected, the light 7.3 illuminates but the

door remains locked to indicate that the water must be

emptied out before opening the door.

Follow the below instructions to empty out the water:

1. Turn the programme selector dial to O .

2. Select the draining or spinning programme.

to cancel a programme which