Directed Xpresskit DBALL2 Manual de instalación - Página 8

Navegue en línea o descargue pdf Manual de instalación para Por cerraduras Directed Xpresskit DBALL2. Directed Xpresskit DBALL2 18 páginas. Ford5 remote start ready (rsr) installation
También para Directed Xpresskit DBALL2: Manual de instalación (12 páginas), Manual de instalación (19 páginas), Manual (14 páginas), Manual de instalación (13 páginas), Manual de instalación (14 páginas), Manual de instalación (19 páginas), Manual de instalación (16 páginas), Manual de instalación (20 páginas), Manual de instalación (15 páginas), Manual de instalación y consulta rápida (16 páginas), Manual de instalación (18 páginas), Manual de instalación (16 páginas), Manual de instalación (18 páginas), Manual de instalación (16 páginas), Manual (19 páginas)

Imprimir página
Directed Xpresskit DBALL2 Manual de instalación
Platform: DBALL2
Firmware:
HYUNDAI4

Module Programming

Refer to the
LED
Diagnostics section on page 2 for more information and for troubleshooting purposes.
Important
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the
function programming is selected using Xpress
version of the application.
Warning!
To take advantage of advanced features, you must use Xpress
Flashing a module using your computer:
1. Connect the interface module to your computer using the
XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and
select the
Config for RSR
3. Follow the instructions to select your vehicle, installation
type, and configure your options.
4. Once you have configured the firmware options, click on the
FLASH button.
When the flashing operation is successful, you can proceed with the programming instructions below.
SmartStart Installation
The
DBALL
module
must
be connected to it. Failing to do so could damage
a.
To
ensure that the D2D communication between SmartStart and
Gray wire must be connected to a ground source (
loop must be cut (
Rev A
b.
Do
NOT
connect the 2-pin harness (on SmartStart). Power and ground will be provided by
the
DBALL2
D2D connector.
Connect SmartStart to
DBALL
OR
XL202 Installation
Connect
XL
202 to
DBALL2
Connect the 10-pin
1
DBALL, then w
ait until the
IMPORTANT:
Do
2
Press
the Push-To-Start (PTS) button
the ignition ON.
The orange
LED
3
and shuts off.
4
Press the Push-to-Start (PTS) button
You have successfully completed the
Remote Start Ready
1
XL
202 or SmartStart module to
VIP
(version 4. or higher). Visit www.directechs.com to download the latest
button.
be disconnected from any power source before SmartStart can
DBALL
Rev B
SmartStart).
using the D2D port.
using the D2D port.
, 1
2-pin
and 14-pin
harnesses to
LED
turns
ON
solid red
NOT
press the brake pedal.
twice
flashes then the green
LED
once
module
programming sequence.
(RSR)
Installation
DBALL
2, it is important to ensure that the proper feature and
5
VIP
4.5 (and higher) or the Directechs Mobile app.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your
2. Launch the Directechs Mobile app on your smartphone or
tablet.
3. Select
FLASH YOUR MODULE
instructions.
. 2
DBALL
works properly, the
SmartStart), and the Brown or Blue
.
st
1
to turn
turns
ON
for 3 seconds
more to turn the ignition OFF.
Rev.: 20170814
XKL
oader3.
and follow the on screen
SmartStart
XL202
&
rd
3
nd
2
Do NOT
ENGINE
2X
PUSH
press the
START
STOP
brake pedal
&
&
Solid Green or
Flashes
Orange x3 sec
ENGINE
1X
PUSH
START
STOP
© 2017 Directed. All rights reserved.
Page 8
Solid
Off