Directed Xpresskit DBALL2 Manual de instalación - Página 8

Navegue en línea o descargue pdf Manual de instalación para Por cerraduras Directed Xpresskit DBALL2. Directed Xpresskit DBALL2 18 páginas. Ford5 remote start ready (rsr) installation
También para Directed Xpresskit DBALL2: Manual de instalación (12 páginas), Manual de instalación (19 páginas), Manual de instalación (18 páginas), Manual (14 páginas), Manual de instalación (13 páginas), Manual de instalación (14 páginas), Manual de instalación (19 páginas), Manual de instalación (16 páginas), Manual de instalación (20 páginas), Manual de instalación (15 páginas), Manual de instalación y consulta rápida (16 páginas), Manual de instalación (18 páginas), Manual de instalación (16 páginas), Manual de instalación (16 páginas), Manual (19 páginas)

Imprimir página
Directed Xpresskit DBALL2 Manual de instalación
Platform: DBALL2
Firmware:
CHRYSLER Remote Start Ready

Module Programming

Refer to the
LED
Diagnostics section on page
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the
function programming is selected using Xpress
version of the application.
Warning!
To take advantage of advanced features, you must use Xpress
available functions and features.
1. Connect the interface module to your computer using the
2. Open an Internet Explorer browser (version 6 or higher), and go to www.
that is currently saved on the interface module will be indicated in the top left corner of the page.
3. Select the
year make
,
and
4. In the search result page, select one of the available install options (config for
instructions provided on the screen.
5. Once you have configured your options, click on the
6. The following message will be displayed when the upload is completed:
"The flashing is successfully completed. You may now unplug the kit."
You can now proceed with the programming instructions below.
SmartStart Installation
The
DBALL
module
must
be connected to it. Failing to do so could damage
a.
To
ensure that the D2D communication between SmartStart and
Gray wire must be connected to a ground source (
loop must be cut (
Rev A
b.
Do
NOT
connect the 2-pin harness (on SmartStart). Power and ground will be provided by
the
DBALL
D2D connector.
Connect SmartStart to
DBALL
OR
XL202 Installation
Connect
XL
202 to
DBALL
using the D2D port.
Connect the 10-pin
1
DBALL, then w
ait until the
Insert the key into the ignition barrel without turning it and wait for
3
the
LED
to flash orange.
T
urn
the key
it to the
flash orange. It will then turn
3 seconds, before turning
4
Refer to
the
LED
troubleshooting if the
orange within 15 seconds.
When the
LED
turns
5
and r
emove
it
from the ignition barrel.
4
10
XL
202 or SmartStart module to
VIP
(version 4. or higher). Visit www.
model
of the vehicle; the page will refresh to display the compatible firmware.
FLASH
be disconnected from any power source before SmartStart can
DBALL
Rev B
SmartStart).
using the D2D port.
, 1
2-pin
and 14-pin
harnesses to
LED
turns
ON
solid red
ON
position. The
LED
ON
solid green
OFF
.
Diagnostics section
on page
LED
does not turn
ON
OFF urn the key to the
, t
(RSR)
Installation
for more information and for troubleshooting purposes.
DBALL
, it is important to ensure that the proper feature and
5
directechs
VIP
4.5 or higher. Using version 2.9 or 3.1 will limit
XKLoader
.
directechs
.com. The detail of the platform and firmware
RSR RXT
,
button to upload the firmware onto the interface module.
.
DBALL
works properly, the
SmartStart), and the Brown or Blue
.
st
1
will continue to
Key IN
OR
orange for
9 for
solid green
OR
OFF
position
Rev.: 20170817
.com to download the latest
or Standard install), and follow the
SmartStart
XL202
rd
3
nd
2
Key IN
&
START
or
&
START
Solid
&
Off
Key OUT
&
Off
© 2017 Directed. All rights reserved.
Page 8
&
Solid
Flashes
Solid
START