Ctouch Laser Nova Manual de inicio rápido - Página 2

Navegue en línea o descargue pdf Manual de inicio rápido para Pantalla táctil Ctouch Laser Nova. Ctouch Laser Nova 2 páginas.

Imprimir página
The power to engage
CONTROL PANEL
1
2
3
4
5
6
nr.
Description
1
USB(2.0)(for camera)
This port is for connecting a camera.
Notes:
1. Please open the dust cover before being used.
2. It can perfectly support cameras up to 720p.
2
Microphone
Voice input.
3
UP-Android Module
Insert an UP-Android module.
4
OPS module slot
Insert an OPS module (Optional).
5
Power LED
Red: In standby mode.
Blue: In power on mode.
Remote control sensor
Aim the remote control towards this spot on the CTOUCH interactive display.
Power
Press to switch the CTOUCH interactive display on or off.
Note: When the CTOUCH interactive display is turned on, press the button in the middle
to show the Float Bar. Press the button for about 2 seconds and the screen will go into
stand-by mode.
6
USB
Connect USB devices to this port for OPS and Android.
7
AC IN
Plug the AC cord into this jack and into a power outlet. (AC 100-240V 50/60Hz)
8
Fuse
12A 250V
9
Power Switch
Push ( I ) to turn on the power, push (O) to cut off the power.
Note: Don't cover the power switch.
Laser Nova | Quick start guide CTOUCH Europe b.v. - imPD
LaserNova_QSG3luik_EnglishV18405-03.indd 2
crease
CONNECTION PANEL
7 8 9
nr.
1
Antenna
2
USB (Type-C)
3
USB
4
USB
5
HDMI1/2/3 IN
6
DP(DisplayPort) IN
7
PC IN
8
RS-232C
9
10
S/PDIF digital audio OUT
11
TOUCH OUT 1/2
12
LAN
Note: If the CTOUCH display is on the VGA source and does not get any signal, it will go into stand-by mode after two minutes.
When the CTOUCH display is on others sources and does not get any signal, it will go into stand-by mode after 10 minutes.
1
2
C
3.0
3
2.0
1
4
2.0
5
6
7
8
9
10
11
12
Description
WiFi antenna. (Tighten the WiFi antenna in clockwise direction).
Connect USB devices to this port for Android.
Connect USB devices to these ports for Android.
Connect USB devices to this port for Android.
Note: use this USB-port for software updates.
Connect an HDMI or DVI device to this HDMI port.
HDMI3(ARC): Connect an ARC-enabled home theater receiver to this HDMI port.
Connect a DP device to this DP port.
Connect the video/audio of a computer to these ports.
For remote control, service and other uses.
Connect headphones to this jack. The current selected source is audible.
Connect a digital sound system to this S/PDIF jack.
Output for external devices connected to PCx, HDMIx or DP ports, which support touch
systems.
Connects the external network or router.
crease
POWER ON / OFF
TURNING THE CTOUCH INTERACTIVE DISPLAY ON OR OFF
1. Plug the power cord into an AC power outlet.
2.
Switch the Power Switch on the CTOUCH interactive display on.
3. The display is in standby mode now. Wait a moment until the power indicator lights up, then press
NOTE: Be sure to wait for a few seconds before pressing
button. If you promptly press
the CTOUCH interactive display may act wrongly or not respond at all.
4. Press
button again to put the display in standby mode.
5.
Switch the Power Switch off to cut off the power completely.
NOTE: If the CTOUCH display is on the VGA source and does not get any signal, it will go into stand-by mode after two minutes.
When the CTOUCH display is on others sources and does not get any signal, it will go into stand-by mode after 10 minutes.
CONNECTIONS
•
Make sure both the external device as well as the CTOUCH display are turned off, when connecting the external device to the CTOUCH display.
•
Check the plugs at the ends of the cables to make sure that they are the correct type, before
plugging them into the jacks of the CTOUCH interactive display.
FIRST TIME INSTALLATION
When turning on the CTOUCH display for the first time, the below shown installation menu pages will appear on the screen.
Select the desired menu language. Press
Select your location and press NEXT to go to
START to go to the next page.
the next page.
CONNECTING TO THE INTERNET
WIRED
Plug the LAN-cable into the LAN-port on the bottom of the CTOUCH display, to connect to the internet.
WIRELESS
Click on the Android Menu button in the Float bar.
Click on 'Wi-Fi
Turn the Wi-Fi on (top right corner). Select
the connection you want to connect with.
to turn on the CTOUCH interactive display.
Select your required Energy Saving Mode
and press NEXT to finish the installation.
Fill in your password and press 'Connect'.
05-04-18 16:13