Clarus Fusion Series Manual del usuario - Página 14

Navegue en línea o descargue pdf Manual del usuario para Sistemas de filtración de agua Clarus Fusion Series. Clarus Fusion Series 20 páginas. Treatment systems
También para Clarus Fusion Series: Manual del usuario (20 páginas)

Imprimir página

CONTAINER

Aeration

The aeration system must be flushed every maintenance

visit. There are two flushing methods: (A) Air flushing and (B)

Water flushing. Air flushing must be done every maintenance

visit. Water flushing may be done if there is a sign of

clogging in the aeration chamber (e.g. abnormal increase in

recirculation flow).

Figure 18

FAUCET

BACKFLOW PREVENTER

BLOWER

(A) Air flushing procedure:

• Make sure the blower is in the aeration mode.

• Make sure a check valve or backflow preventer is present

for water flushing procedure.

• Close gray recirculation valve (2) all the way. (0%)

• Rotate blue aeration valve (1) back and forth from the 0%

to the 100% position several times to flush.

• Set valves (1) and (2) back to the appropriate positions.

(See Recirculation Flow Adjustment, pg. 10)

(B) Water flushing procedure: (See Figure 18)

• Make sure the blower is off.

• Close valve (2) all the way.

• Connect a water line to the aeration line as shown in

Figure 18.

• Gradually open the water faucet and introduce water

into the system.

• Rotate valve (1) back and forth from the 0% to the 100%

position several times to flush.

• Turn off the water, remove the water line, and reconnect

the air line to the blower.

• Set valves (1) and (2) back to the appropriate positions.

(See Recirculation Flow Adjustment, pg. 10)

(C)

Cleaning the recirculation line:

• Make sure the blower is in the aeration mode. If not,

change the mode by pressing the Manual Backwash

button.

• Open the gray recirculation valve (2) to 100%.

• Flush water through the recirculation line for several

seconds.

• Turn off the recirculation by rotating the gray valve

(2) to 0%.

• Make sure the blower is off. Allow the system to

relax for a few seconds.

• Repeat this cleaning method three times.

• A hose or brush can also be used to clean the recirculation

line. See Figure 20.

• Reset the gray valve (2) to its original position.

AERATION CHAMBER CLEANING

HOSE

CLAMP

G.L

EXISTING AIR LINE

TO TREATMENT UNIT

CONTAINER

FAUCET

BACKFLOW PREVENTER

Backwash

The backwash system must be flushed every maintenance.

There are two flushing methods: (A) Air flushing and

(B) Water flushing.

maintenance visit. Water flushing must be done if there is

a sign of clogging in the aeration chamber (e.g. abnormal

increase in recirculation flow).

(A) Air flushing procedure:

• Make sure the blower is in the backwash mode.

• Close the gray sludge transfer valve (4) all the way.

• Rotate the red backwash valve (3) back and forth from the

0% to the 100% position several times to flush.

• Set valves (3) and (4) back to the appropriate positions.

(See Backwash System)

Figure 19

BRUSH

• Turn off the water, remove the water line, and reconnect the

airline to the blower.

RECIRCULATION OR BACKWASH PIPE

• Set valves (3) and (4) back to the appropriate positions. (See

Backwash System)

• Make sure that the blower is in the backwash mode. If

not change the mode by pressing Manual Backwash.

• Open the gray sludge transfer valve (4) to 100%.

• Flush water through the sludge transfer line for a few

seconds.

• Repeat this cleaning method three times.

• A hose or brush can also be used to clean the sludge

transfer line. See Figure 20.

• Reset the gray valve (4) to its original position.

• Return the blower to the normal aeration mode. by

HOSE

pressing Manual Backwash.

BLOWER

Figure 20

CLAMP

G.L

EXISTING AIR LINE

TO TREATMENT UNIT

Foam formation

Make sure there is not an excess amount of foam on the

surface. If excessive foam is present it may indicate high

detergent usage. Meet with owners to inform and educate

them concerning excessive use.

Abnormal water level

If the water level exceeds the partition wall, clean the plastic

cage first with a brush, then check for possible clogging in the

filter media section. Clogs may be cleared by using a manual

backwash tool. The manual backwash tool may also be used

to eliminate a clog in the anaerobic chamber media as well.

Air flushing must be done every

(B) Water flushing procedure:

(See Fig. 19)

• Make sure the blower is off.

• Close valve (4) all the way.

• Connect a water line to the backwash

airline as shown in Figure 18.

• Gradually open the water faucet and

introduce water into the system.

• Rotate valve (3) back and forth from

the 0% to the 100% position several

times to flush.

BRUSH