Cub Cadet 19B70064100 Hoja de instalación
Navegue en línea o descargue pdf Hoja de instalación para Accesorios para cortacéspedes Cub Cadet 19B70064100. Cub Cadet 19B70064100 2 páginas. 48"/54"/60" mulch kit
Imprimir página
4
48" Deck
5
54" Deck
6
60" Deck
Blade Installation
Before beginning installation, place the tractor on a firm and level surface, set the
parking brake, place the PTO in the disengaged (OFF) position, stop the tractor's engine
and remove the ignition key to prevent unintended starting.
Cutting blades are sharp. Always protect hands by wearing heavy leather work gloves
to grasp blades.
1.
Remove cutting deck from beneath tractor as instructed in your Operator's Manual.
2.
Gently flip deck over to expose
its underside.
IMPORTANT!
Flipping the deck will require
two people.
3.
Place a block of wood between deck
housing baffle and cutting blade to
act as a stabilizer, then use a wrench
to remove hex flange nut securing
each blade to its spindle assembly. See
Figure 2.
IMPORTANT!
Hex flange nuts have a
right-handed (normal) thread pattern. Do NOT
attempt to force nuts in opposite direction.
Doing so may damage nut.
4.
Remove chute deflector baffle from
underside of deck by removing two
carriage bolts and flange lock nuts
that secure it to deck. See Figure 3.
5.
When baffle is removed, re-install one
carriage bolt and flange lock nut into
deck in most central opening. See
Figure 3.
NOTE:
Replacing hardware keeps material
from escaping the deck.
6.
Replace blades with blades included in
kit. Be sure to install each blade with
side marked ''Bottom'' (or with a part
number stamped on it) facing the ground when mower is in operating position.
IMPORTANT!
Use a torque wrench to tighten each blade spindle's hex flange nut to between 90 ft-lb
and 110 ft-lb.
7
10
8
11
9
12
Figure 1
WARNING
WARNING
Figure 2
Figure 3
CUB CADET LLC, P.O. BOX 361131, CLEVELAND, OHIO 44136-0019
19B70064100 (48"); 19B70065100 (54"); 19B70066100 (60") -- Mulch Kit
Contents of Carton
13
Ref
1
2
1
3
4
2
14
5
6
7
3
8
9
10
15
11
12
13
14
15
Baffle Installation
Do not remove cutting deck's discharge chute when operating mower with mulch
kit installed.
1.
Install center baffle using four 3/4"
carriage bolts (710-3178) and four hex
flange nuts (712-05007). See Figure 4.
2.
Install discharge baffle in the
following order:
a.
Install discharge baffle to
underside of top of deck with
two 1" carriage bolts (710-
3168) and two hex flange nuts
(712-05007). See Figure 5.
Figure 5
b.
Working from inside out,
secure discharge baffle to
outside wall of deck with two
1" carriage bolts (710-3168)
and two hex flange nuts (712-
05007). See (1) in Figure 6.
c.
Stabilize discharge baffle by
connecting it to previously
installed center baffle with two
3/4" carriage bolts (710-3178)
and two hex flange nuts (712-
05007). See (2) in Figure 6.
3.
Install left baffle using three 3/4"
carriage bolts (710-3178) and three hex flange nuts (712-05007). See Figure 7.
Part #
Description
710-3168
Carriage Bolt 3/8-16 X 1.00 Gr5
710-3178
Carriage Bolt 3/8-16 X 0.75 Gr5
712-05007
Hex Flange Nuts
742-04278A-X
XTREME™ Mulch Blade (48" Deck)
01005380-X
XTREME™ Mulch Blade (54" Deck)
01005381-X
XTREME™ Mulch Blade (60" Deck)
689-02359
Discharge Baffle (48" Deck)
689-02360
Discharge Baffle (54" Deck)
689-02362
Discharge Baffle (60" Deck)
703-07182A
Center Baffle (48" Deck)
703-07194
Center Baffle (54" Deck)
703-07178A
Center Baffle (60" Deck)
703-07210A
Left Baffle (48" Deck)
703-07193A
Left Baffle (54" Deck)
703-07177A
Left Baffle (60" Deck)
CAUTION
Figure 4
1
Figure 6
Figure 7
Installation Sheet
Qty
4
9
13
3
3
3
1
1
1
1
1
1
1
1
1
2
Form No. 769-23150A
September 17, 2020