ARO ARO PH10A-BSS-SST Manual del usuario - Página 2
Navegue en línea o descargue pdf Manual del usuario para Bomba de agua ARO ARO PH10A-BSS-SST. ARO ARO PH10A-BSS-SST 9 páginas. 1” high pressure diaphragm pump
Imprimir página
READ, UNDERSTAND, AND FOLLOW THIS INFORMATION TO AVOID INJURY AND PROPERTY DAMAGE.
EXCESSIVE INLET AIR PRESSURE
STATIC SPARK
EXPLOSION HAZARD
WARNING EXCESSIVE AIR PRESSURE. Can cause pump
damage, personal injury or property damage.
Do not exceed the maximum inlet air pressure as stated on the
S
pump model plate.
Be sure material hoses and other components are able to with-
S
stand fluid pressures developed by this pump. Check all hoses
for damage or wear. Be certain dispensing device is clean and
in proper working condition.
WARNING STATIC SPARK. Can cause explosion resulting in
severe injury or death. Ground pump and pumping system.
Sparks can ignite flammable material and vapors.
S
The pumping system and object being sprayed must be
S
grounded when it is pumping, flushing, recirculating or spray-
ing flammable materials such as paints, solvents, lacquers,
etc. or used in a location where surrounding atmosphere is
conducive to spontaneous combustion. Ground the dispens-
ing valve or device, containers, hoses and any object to which
material is being pumped.
Use the pump grounding lug provided on metallic pumps for
S
connection of a ground wire to a good earth ground source.
Use AROR part no. 66885-1 ground kit or a suitable ground
wire (12 ga. / 2.6 mm min. dia.).
Secure pump, connections and all contact points to avoid
S
vibration and generation of contact or static spark.
Consult local building codes and electrical codes for specific
S
grounding requirements.
After grounding, periodically verify continuity of electrical path
S
to ground. Test with an ohmmeter from each component (e.g.,
hoses, pump, clamps, container, spray gun, etc.) to ground to
insure continuity. Ohmmeter should show 0.1 ohms or less.
Submerse the outlet hose end, dispensing valve or device in
S
the material being dispensed if possible. (Avoid free streaming
of material being dispensed.)
Use hoses incorporating a static wire.
S
Use proper ventilation.
S
Keep inflammables away from heat, open flames and sparks.
S
Keep containers closed when not in use.
S
WARNING INJECTION HAZARD. Any material injected into
flesh can cause severe injury or death. If an injection occurs,
immediately contact a doctor.
Do not grab front end of dispensing device.
S
Do not aim dispensing device at anyone or any part of the body.
S
Disconnect air supply line and relieve pressure from the sys-
S
tem by opening dispensing valve or device and / or carefully
and slowly loosening and removing outlet hose or piping from
pump.
WARNING HAZARDOUS PRESSURE. Can result in serious
injury or property damage. Do not service or clean pump,
hoses or dispensing valve while the system is pressurized.
WARNING HAZARDOUS MATERIALS. Can cause serious in-
jury or property damage. Do not attempt to return a pump to the
Page 2 of 8
OPERATING AND SAFETY PRECAUTIONS
HAZARDOUS MATERIALS
HAZARDOUS PRESSURE
factory or service center that contains hazardous material.
Safe handling practices must comply with local and national
laws and safety code requirements.
Obtain Material Safety Data Sheets on all materials from the
S
supplier for proper handling instructions.
WARNING EXPLOSION HAZARD. Models containing alumi-
num wetted parts cannot be used with III.-Trichloroethane, Me-
thylene Chloride or other Halogenated Hydrocarbon solvents
which may react and explode.
Check the pump wetted parts for compatibility before using
S
with solvents of this type.
CAUTION Verify the chemical compatibility of the pump
wetted parts and the substance being pumped, flushed or re-
circulated. Chemical compatibility may change with tempera-
ture and concentration of the chemical(s) within the
substances being pumped, flushed or circulated. For specific
fluid compatibility, consult the chemical manufacturer.
CAUTION Maximum temperatures are based on mechani-
cal stress only. Certain chemicals will significantly reduce
maximum safe operating temperature. Consult the chemical
manufacturer for chemical compatibility and temperature lim-
its. Refer to Pump Data on page 1 of this manual.
CAUTION Be certain all operators of this equipment have
been trained for safe working practices, understand it's limita-
tions and wear safety goggles / equipment when required.
CAUTION Do not use the pump for the structural support of
the piping system. Be certain the system components are
properly supported to prevent stress on the pump parts.
Suction and discharge connections should be flexible connec-
S
tions (such as hose), not rigid piped, and should be compatible
with the substance being pumped.
CAUTION Prevent unnecessary damage to the pump. Do
not allow pump to operate when out of material for long periods
of time.
Disconnect air line from pump when system sits idle for long
S
periods of time.
NOTICE
Replacement warning label pn 92325 and solvent
reaction warning tag pn 92769 are available upon request.
= Hazards or unsafe practices which could
WARNING
result in severe personal injury, death or
substantial property damage.
= Hazards or unsafe practices which could
CAUTION
result in minor personal injury, product or
property damage.
= Important installation, operation or
NOTICE
maintenance information.
INJECTION HAZARD
PH10A-XXX-XXX (en)