Dish Network 222 TV1 Manual - Página 2

Navegue en línea o descargue pdf Manual para Receptor Dish Network 222 TV1. Dish Network 222 TV1 2 páginas. Quick facts; quick remote control programming & tips for installers

Imprimir página

Remote Antenna

• The UHF remote control antenna

MUST be connected to R

port on the rear of each

NTENNA

applicable receiver for proper

UHF remote/receiver operation.

Teaching/Learning Remotes

• The IR address from the

"teaching remote" must match

the IR address of the receiver.

For example, if the DISH Network

IR remote used to teach the

universal remote is set to address

4, the address of the receiver

must also be set to address 4.

• Because the DISH 811 & DISH

Player-DVR 921 receivers ship

with UHF Pro only remote

controls, both receivers have a

"Teach Remote" feature, so that

the UHF Pro remote can be used

to tell the receiver to blast IR

commands out to a learning

remote.

• IR commands from any of our

past remotes (excluding

7100/7200) can be used to

program a universal IR learning

remote.

• The EZ remote uses a

"broadcast" IR address. If used to

teach a universal remote, it will

not matter what address the

receiver is set to.

Receivers

Feature

111* ViP 211*

Receives IR

Yes

Receives

UHF Pro

*The IR-to-UHF Pro Upgrade Kit can be purchased to provide remote control operation from a distance.

**TV1 can be controlled by UHF Pro when using the applicable replacement remote control with a TV1 UHF Pro key installed.

Quick Remote Control Programming

& Tips for Installers

UHF Pro Remotes

• UHF Pro technology is not

EMOTE

compatible with UHF. A UHF Pro

receiver cannot be controlled using

the UHF signal from a UHF remote.

A UHF receiver cannot be

controlled by the UHF Pro signal of

a UHF Pro remote.

• For UHF Pro remotes with an A/B

switch inside the battery

compartment: If you use a UHF Pro

remote near another UHF Pro

remote on the same frequency (for

example, another receiver in the

home, or a neighbor has one),

selecting the other band tells the

remote to use a different remote

frequency, and eliminates conflicts

with the other remote control(s).

For use with DISH Player-DVR 942,

ViP622 DVR and later dual-tuner

receivers only.

Dual-Tuner Receivers

• TV1 of dual-tuner, two-TV receivers

can be configured to accept either

IR or UHF Pro commands. A TV1

UHF Pro key installed in the remote

is required. Use the replacement

remote's user guide to ensure the

correct TV1 UHF Pro key is used

(one is for DISH Player-DVR

522/625, one is used for all

others).

• TV2 of dual-tuner, two-TV receivers

is UHF Pro ONLY.

• The TV2 remote control for dual-

tuner, two-TV receivers can be

configured for use as an IR remote

control for TV1 or as a UHF Pro

remote control for TV2 (the TV2

remote ships with the blue UHF Pro

key installed).

222

311*

TV1

TV2

Yes

Yes**

Yes

Contents subject to change without notice.

EchoStar Technologies Corporation

322

522/625

TV1

TV2

TV1

TV2

Yes

Yes**

Yes

Yes**

Yes

Page 2 of 2

UHF/UHF Pro Reception Tips

• Make sure the satellite

receiver's UHF antenna and tip

is away from metal objects,

wiring, and electronics (DVD

player, etc.) located on a shelf

above or below the satellite

receiver. The antenna should

be angled away so the tip is

separated from the electronics

by a couple of inches if

possible. Also, shifting the

position of the satellite

receiver on the shelf may help.

• For dual-tuner, two TV

receivers, if the TV2 room is a

floor or two above or below

where the receiver is located,

it might help to orient the

antenna as horizontal (flat) as

possible.

• It may help to move the

antenna away from the back of

entertainment center wiring

and other electronics with a

length of RG-6 cable (3 to 5

feet).

• A 6 to 15 dB F-connector

attenuator (from Radio Shack,

etc.) can be installed in

between the UHF antenna input

and the antenna to improve

performance in certain

circumstances. This works best

for distances of up to

approximately 75 feet within a

residence.

• Combining the RG-6 cable

extension with the attenuator

might be needed if the prior

steps are not effective.

942

811

921

TV1

TV2

Yes

Yes**

Yes

ViP622

TV1

TV2

Yes

Yes**

Yes

Rev. 7/17/2006