ClearWater Lights CANopener Manual - Página 2

Navegue en línea o descargue pdf Manual para Accesorios para motocicletas ClearWater Lights CANopener. ClearWater Lights CANopener 13 páginas.

ClearWater Lights CANopener Manual
The table below is only a quick summary guide of all the CANopener features. See
The table below is only a quick summary guide of all the CANopener features. See
Step 1: Parts List and Bike Preparation
the details of each feature throughout this manual.
the details of each feature throughout this manual.
BIKE MUST BE RUNNING TO TOGGLE THROUGH MODES BELOW
TSC = Turn Signal Cancel WW = Wonder Wheel (BMW multifunction controller)
TPM = Tire Pressure Monitor FTP = Flash To Pass OBL = Optional Brake Light
Function
Darla/Glenda
Dimmer
[Pg. 5]
Erica/Krista/Sevina
Dimmer
[Pg. 5]
Erica/Krista/Sevina
On/Off
Darla On/Off
(Version 2.3 and later)
High Beam
Mode
[Pg. 7]
Horn Activation
Mode
[Pg. 6]
Hazard
Flasher
Alert Mode
[Pg. 7]
Turn Signal
Dimming
[Pg. 6]
Clearwater
Brake Light
(optional)
[Pg. 8]
Inertial Braking
[Pg. 8-9]
Brake Dimming
Reset
Default
Settings
[Pg. 9]
Page 2

Summary of CANopener features and operation

Summary of CANopener features and operation
Command
Press and release (TSC), then
Hold control wheel Left for 2
seconds and rotate to adjust.
Press (TSC) again to lock in.
Press and release (TSC), then
hold control wheel right for 2
seconds and rotate to adjust.
Press (TSC) again to lock in.
Hold TSC for 2 seconds
Hold TSC Left for 5 seconds to
turn OFF
Hold TSC Right for 3 seconds to
turn back ON
Press and release (TSC), hold
brake lever and press & release
FTP 5 times to toggle
Press and release TSC, then
hold brake lever and press &
release TSC 5 times to toggle
Press and release (TSC), hold
hazard switch then press &
release brake lever 5 times to
Press and release (TSC), hold
right turn signal then press &
release front brake lever 5 times
While stationary, press & release
TSC then press & release the
front brake lever 5 times within 5
seconds to toggle
Press & release TSC then press
& release the foot brake lever 5
times within 5 seconds to toggle
See brake light manual
Press and release (TSC), hold
left turn signal then press &
release FTP 6 times within 6
seconds.
**NOTE**
**NOTE**
VERSION 2.4
Default setting in
RED
Rotate WonderWheel to select 10 brightness
levels (10% to 100%) To adjust brightness on
High Beam Mode, turn on high beam first.
Dimmer control will cancel after 2 seconds or
by pressing TSC
Mode 1 - on and dimmable (default)
Mode 2 – off
Mode 1 - on and dimmable (default)
Mode 2 – off
Mode 1 - all lights on 100% with high beam or
FTP, Krista/Erica/Sevina must be turned on
Mode 2 - Same as Mode 1 except
Krista/Erica/Sevina lights don't have to be
turned on. (default)
Mode 3 - Same as Mode 2 but lights will
strobe for 2 seconds if FTP is pressed 3
times (Version 1.91 and later)
Mode 1 - horn does not affect lights
Mode 2 - horn activates lights 100% (default)
Mode 3 - lights strobe with horn
Mode 1 - no flash (default)
Mode 2 - lights strobe while holding hazard
switch (Version 1.90 and earlier). Lights
toggle
strobe when hazards are toggled on (Version
1.91)
Mode 1 - off (default)
Mode 2 - lights dim when turn signals are
activated.
Mode 1 - off (default on Version 1.6 and
older)
Mode 2 - functions identically to BMW brake
light (default on Version 1.7 and later)
Mode 3 - California legal strobe on brake
activation (4Hz flash)
Mode 4 – speed sensitive (flashes faster and
brighter with harder braking) Can be
adjusted.
Mode 1 - Inertial braking disabled
Mode 2 – Low sensitivity. Brake light
activates when engine braking reaches .4G.
Mode 3 – High sensitivity. Brake light
activates when engine braking reaches .2G.
(default)
Reset all functions to the default settings
above.
Page 1
Page 1
Modes
See brake light manual