CustomWorks Dominator Modelo - Página 3

Navegue en línea o descargue pdf Modelo para Coche de juguete motorizado CustomWorks Dominator. CustomWorks Dominator 17 páginas. 1:10 scale 4wd dirt oval car kit

Imprimir página

Bag A

One-Way Assembly

-Parts for

Bag A

3601

Qty 1

One-Way Hub

3605

3601

*Apply CA Glue along the face of

the pulley as shown. 4-6 small

dots of glue will work. DO NOT

allow glue to run into sprocket

teeth!

Bag B

Diff Assembly

-Parts for

Step#1

3613

Qty 1

Right Outdrive

-Parts for

Step#2

3612

Qty 1

Left Outdrive

STEP #1

4361

CUSTOM-TIP!!!

-Using 400 Grit Sandpaper in a"Figure 8"

3609

pattern, it is best to sand the surfaces

of both the 4358 Diff Ring and 4360

4359

Thrust Washers. The textured

4360

3613

1229

- Slide a 4360 Thrust Washer onto the 3609 Diff Bolt.

- Apply a thick layer of Diff Lube to the Thrust Washer, press

(6) 4359 Thrust Balls into the Diff Lube.

- Slide the other Thrust Washer on the Diff Bolt and insert it

into the 3613 Right Outdrive.

- Press (1) 1229 Bearing into the Outdrive.

- Put (1) 4358 Diff Ring on the Outdrive, apply Diff Lube as

shown.

3602

Qty 1

One-Way Pulley

3602

PULLEY

4358

Qty 2

4360

Diff Ring

Thrust Washer

4362

Qty 1

Diff Spring

surface results in a smoother and

longer lasting diff.

4358

DIFF

LUBE

3602

Qty 1

Pulley Ring

* CA GLUE ALONG THIS FACE

3602

RING

3605

5292

Qty 2

4361

Qty 1

Diff Bolt Cover

3615

Qty 1

3615

Diff Pulley

Pulley Ring

3613

- Attach the 3615 Pulley Ring to the

One-Way Pulley using 4-6 small dots of CA Glue

where the faces of the two parts meet.

- Press (1) 1229 Bearing and the (12) 4357 Diff Balls into the

Diff Pulley. Use Diff Lube as shown.

- Put (1) 4358 Diff Ring onto the 3612 Left Outdrive, apply Diff

Grease as shown.

- Install the 4362 Diff Spring and 4361 T-nut into the Outdrive.

- Carefully slide the diff assembly together so the Diff Bolt passes

thru the entire assembly and threads into the T-nut.

- Screw the Diff Bolt into the T-nut until you feel the Diff Spring

fully compress. DO NOT OVERTIGHTEN!!! Back the Diff Bolt off

EXACTLY 1/8 of a turn. Diff motion should be smooth and the

Outdrives will turn in opposite directions.

3605

Qty 2

One-Way Outdrive

- Mount 3602 One-Way Pulley to the 3601 One-

Way Hub using (4) 5292 Screws.

- Attach the 3602 Pulley Ring to the One-Way

Pulley using 4-6 small dots of CA Glue where the

faces of the two parts meet.

- Slide 3605 One-Way Outdrives into the bear-

ings pressed into the One-Way Hub.

1:1

4359 Qty 6

3609

Qty 1

Thrust Balls

Dominator Diff Bolt

Qty 1

4357

Qty 12

Diff Balls

STEP #2

3615

4357

X12 1229

1:1

5292

Qty 4

M2.5 x 4 BH Screw

1:1

1229

Qty 2

5/32 x 5/16 Bearing

4361

Qty 1

Diff T- Nut

4358

3612

4362

4361